Diesel Coolants: The Right Fluid For The Right Application

Diesel Coolants: The Right Fluid For The Right Application

Which antifreeze should you use in your diesel engine? It seems just when you think that things are starting to settle down, some spec changes. Engine oil has been a hot topic over the past several months and has seen many changes over the past 10 years.

Which antifreeze should you use in your diesel engine? It seems just when you think that things are starting to settle down, some spec changes. Engine oil has been a hot topic over the past several months and has seen many changes over the past 10 years. Antifreeze has also undergone changes and seems to be a hot topic. The frightening fact is that many diesel engine owners are unaware of these changes, which could result in a major catastrophe down the road. Hopefully, this information will benefit you and your diesel engine customers.

For years, we used the typical, green antifreeze formulation. Conventional heavy-duty antifreeze coolants used inhibitors known as SCAs (Supplemental Coolant Additives) that were composed of IAT (Inorganic Acid Technology), which are inorganic compounds such as silicates and phosphates. SCAs were very important in maintaining proper health for a diesel engine because they help prevent small air bubbles from forming around the cylinder liners, which could chip away at the liner. The chipping effect would eventually eat through the liner into the cylinder wall. When this happens, coolant gets into the engine oil and combustion chamber and can eventually destroy the engine.

Heavy-duty, green antifreeze often needs a check on the SCA levels during maintenance intervals. If the SCAs are becoming depleted, a supplemental SCA known as coolant conditioner can be added to help boost levels back where they need to be. Conventional coolant does not have a very long life and should be changed roughly every two years.

Conventional Coolants

  • Silicates for aluminum protection
  • Nitrites for liner cavitation protection
  • Other inhibitors for copper and iron protection

Toward the late 1990s, ELC (Extended Life Coolant) was introduced, which allowed for much longer intervals before the inhibitors needed to be replaced. ELC contained inhibitors known as OAT (Organic Acid Technology) or Nitrited Organic Acid Technology (NOAT), which deplete slower than traditional inorganic silicate and phosphate compounds. This type of coolant can be used for up to 300,000 miles or 6,000 hours of engine operation. Even at this mileage, the coolant can be charged with an extender additive and continue for another 300,000 miles or 6,000 hours of engine operation. ELC requires little or no maintenance. It just needs to be checked every oil change for dilution, clarity, freeze point and color. The color of ELC is usually bright red or pink. Typical ELC can go for up to a five-year interval before changing is recommended.

ELCs (Nitrited Extended Life Coolant)

  • Organic Acid technology for aluminum and iron protection
  • Nitrites for liner cavitation protection
  • Other inhibitors for copper protection

In order to save weight and add fuel economy, some manufacturers opted to use aluminum radiators and other aluminum components for their cooling system. This was a great idea until it became evident that aluminum components in the cooling system were becoming corroded and causing nitrite depletion in the nitrited coolant. The ELC coolant didn’t last as long and caused corrosion, leading to overheating and cooling system problems. The OEMs realized that unless the aluminum components were coated with a non-corrosive film such as metal oxide, the corrosion problem would persist.

With aluminum components in the cooling system, there are two solutions to the corrosion problem. One is to have all of the aluminum components coated to combat the corrosion problem. However, this isn’t cost effective. The second solution is to formulate a coolant that can work in this environment and not have nitrite depletion.

This led to manufacturers incorporating the use of XLC (Extended Life Coolant). This antifreeze uses what is known as an Aliphatic Carboxylate inhibitor, which is nitrite free and made with other somewhat proprietary ingredients. So far, it has worked well as an extended life coolant with a longer drain interval than the ELC. The color of XLC is typically orange in the heavy-duty market, but may be offered in other colors.

XLCs (Nitrite-Free Extended Life Coolant)

  • Organic Acid Technology for aluminum and iron protection along with liner cavitation
  • Other inhibitors for copper protection

Beware of how coolant has changed over the past 10 years. Remember, antifreeze when manufactured is a clear liquid. Different dyes are added to the antifreeze to indicate what type of coolant it represents. Water is the best collector of heat, but the main purpose of antifreeze is not only to cool, but to raise the boiling point and to offer freeze protection, which pure water cannot do.

Pay close attention to your antifreeze choices for automobile and heavy-duty use. Most antifreeze coolants will not mix, and if improperly mixed, may cause major damage. Customers are learning that for modern engines, going to the parts store for simple things such as motor oil or antifreeze isn’t quite so simple anymore. Help them choose the specific fluids that must go into their engine.

Article courtesy Underhood Service.

You May Also Like

Ignition Coil Output

To see inductance inside the primary windings, use an amp probe placed around the positive wire for the ignition coil.

Kilovolts or kV is the unit used to measure the output of an ignition coil. Some coils can output 20kV to 40 kV. So, how does an ignition coil turn system or battery voltage into these huge voltages? The answer is inductance. 

The ECM provides the voltage to the primary coil winding. The primary winding might have 100 turns around the coil’s core or plates. When the voltage to the coil is turned off, a magnetic field collapses. The collapsing field will generate more than 100 volts thanks to inductance. The energy is transformed by the windings in the secondary with inductance again, but thanks to the 10,000 windings, the voltage is boosted to 40kV at the spark plug’s electrodes. The best way to see inductance inside the primary windings is to use an amp probe placed around the positive wire for the ignition coil. With this setup, you can see the current ramping in the coil and the collapse of the magnetic field. 

Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Air Ride Conversion Kits

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring.

Nylon Fuel Line Repair Techniques

Can you repair fuel lines yourself? Yes, if you make quality your number one priority when making decisions.

Understanding Differences Between Aluminum And Cast Iron

Sheer material differences aside, what are the features and benefits of aluminum and iron engine components?

Other Posts

Wheel Speed Sensors and Bearings

The only way to diagnose the sensor and circuit is with a scan tool or scope. 

Timing Chain Systems Need Clean, Quality Oil

Using the wrong oil causes a vehicle’s timing chain to wear quicker.

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

Battery Charging and Programming Diagnostics

Temperature changes how the battery discharges and the amount of current that can be delivered.