Serpentine Belt Tricks and Belt Noise

5 Tricks To Solving Belt Noise

Variables that the engineer did not factor in can put the belt and your diagnostic skills to the test. But there are five techniques you can use to solve belt noise problems.

Engineering a belt system is one of the most difficult jobs for OEMs. There are contact, frictional, centrifugal and peripheral forces that must be taken into account. If they get it right, the belt will be quiet, efficient and last 100,000 miles. If they get it wrong, the belt will be noisy or rob the engine of power. For technicians, the job is even tougher. Variables that the engineer did not factor in can put the belt and your diagnostic skills to the test. But there are five techniques you can use to solve belt noise problems.

1. Remove the Belt

belt500skinny

If you have a hard-to-isolate accessory drive belt noise, try removing the belt and running the engine. If the noise is still present after the belt is removed, it might be an issue with the motor mounts or the timing chain/belt. With the belt off, it is also a great chance to examine the pulleys and belt for potential problems like worn bearings inside the idler pulleys.

2. Tensioner Twist

belt2
Place a wrench on the tensioner and move the arm its entire range of motion at least three times. Feel for spring tension along with a fluid motion throughout. Any sticking or notching movement may indicate a problem with the spring or pivot bearing. The arm should move up and down. Any lateral movement could indicate a bad bearing or spring. Inside some belt tensioners, unseen to most technicians, is a dampening mechanism that absorbs shock. Excessive chattering or tensioner arm movement is not only the result of weak spring tension but also a worn dampener. This makes the tensioner a wear part with a limited life span.

3. Spray it Down

Young Caucasian woman cleaning car, vehicle interior, spray bottle, selective focus

In the 1950s, the sales trick to sell a new belt was to spray a running belt to show that it was slipping or that the noise went away when wet. This trick went away when serpentine belts became more popular. But, this test can be used to isolate worn pulley bearings by eliminating belt noise that could be caused by an alignment problem. Use only water; old-school belt dressing will damage modern EPDM belts and cause more noise.

4. Get in the Groove

2009 LS9 6.2L V-8 SC (LS9)
Like a tire, the friction between the belt and pulleys wears away at the belt, usually on the tops and walls of the ribs. Eventually, the grooves of the pulleys will bottom out on the grooves of the belt, and then the belt will start to slip.
According to one belt supplier, as little as 5% of rib material loss and surface wear can affect how the belt performs, and just 10% belt slippage can affect the overall drivability of a vehicle. Belt manufacturers have simple gauges that can measure groove depth, overall thickness and cracks to quantify wear.

5. Check the Alignment

Pulley alignment tools can help you rule out alignment issues. They can give you the peace of mind that there is a pulley that is out of alignment. It is also a great tool to have if you do a lot of power steering pump or A/C compressor replacement jobs.

Article courtesy Underhood Service.

You May Also Like

Transmission Fluid Hydraulics

You need to know how transmission fluid flows inside an automatic transmission.

Transmission Fluid Hydraulics and Shifting

To understand why using the correct transmission fluid is necessary, you first have to know how the transmission fluid flows inside an automatic transmission. 

Fluid Paths

The journey starts in the pan. The transmission fluid is drawn from the pan through a filter by the pump that is behind the torque converter. The fluid level in the pan and transmission body is critical. Too little, and the transmission will suck air into the pump. Too much transmission fluid and the fluid will come in contact with the rotating components. Both scenarios lead to aeration of the transmission fluid.

How ADAS Systems Perform

When new technologies are applied to driver safety, a higher level of scrutiny and service is required.

Air Ride Suspension Diagnostics

The key to understanding the embedded logic of air ride systems is using service information.

Steering Angle Sensor 101

The steering angle is used by many ADAS functions.

BMW N54 Turbo Problems

Here are some common problems or failures that you should be on the lookout for.

Other Posts
Mercedes-Benz Engine Oil Leaks

Mercedes makes a fine product, but certain repairs will emerge as trends over time.

Brake Pad Wear Sensors

Brake pad wear sensors have been around for years and continue to evolve.

Turbocharger Topics

Turbochargers have made a comeback – and it’s been quick.

Clutch Release Problems

Poor clutch release makes it difficult to start and stop the vehicle or change gears.

Clutch Release