Before The Electric Fuel Pump (Video)

Before The Electric Fuel Pump (Video)

When a mechanical fuel pump comes into your shop, you need to know how to handle it. Sponsored by Carter Engineering.

CC:

When we talk about fuel pumps, we immediately think of electrical pumps in the tank and fuel pump modules. It’s what the majority of cars are equipped with today.

There are, however, quite a few carbureted old cars and trucks on the road that still operate with a mechanical fuel pump. Sooner or later, you’re going to have one in the shop and you’ll need to know the basics to diagnose a fuel system problem.

Most mechanical fuel pumps are driven by the cam shaft. There is a lever that extends out of the pump, which in turn either rides directly on a camshaft lobe or in some cases there is a push rod between the lobe and the pump lever. The lever pivots where it enters the pump transferring motion to a diaphragm and valve assembly, which pressurizes the fuel and delivers it to the carburetor.

The pressure developed by a mechanical pump is not as high as we are used to with electric pumps. It’s usually only about five to six psi, and that’s all you need. Anything higher than that can actually force fuel past the needle and seat and flood the carburetor.

Diagnosing a fuel system with a mechanical pump is a straightforward process, and like any fuel system, pressure is the first thing to look for. Since carbureted vehicles aren’t equipped with a test port, it’s a common practice to disconnect the line from the carburetor, attach a hose to it, and place it in a container and crank the engine.

You’ll know immediately if fuel is being delivered and if you attach the hose to a gauge, you’ll see the pressure output of the pump. There may be cases in which you need to monitor fuel pressure with the engine running, and you’ll have to make an extra fitting between the fuel line and carburetor so you can tee in a pressure gauge. It takes a little extra work because you don’t want to cut or damage the solid line leading to the carburetor.

If fuel delivery is a problem, a tip to remember is to closely inspect all of the fuel lines and hoses. There are normally a couple of spots from the tank all the way up to the engine where there’s a short section of hose instead of hard-line, a pinhole or leak in either the line or one of these hoses will cause the fuel pump to draw in air instead of fuel.

Never overlook the fuel tank. It’s very common to get contaminants in the gas tank of an older vehicle, especially if they have sat for a while. The pickup tubes at the base of the sending units often have fine screens attached to them and they can plug up very easily. If the gas gauge doesn’t work, that’s another clue that there could be rust and corrosion in the tank. The bottom line, if you’ve got a clean tank, good lines, a good pump, and no problems with the pump drive, you’ve got fuel pressure.

When replacing a mechanical pump, be sure to use a high-quality pump from a reputable manufacturer. Fuel pressure specifications are just as important on these old cars and can cause drivability problems just the same on an old vehicle as they will on a new. Thanks for watching.

This video is sponsored by Carter.

You May Also Like

Understanding LSPI & Engine Oil

Discover the importance of using the correct oil specification for your vehicle.

Ever wonder why modern #motoroil is getting thinner? In this episode of Inside the Brands, we dive into the world of motor oil #technology. We explore the rise of turbocharged engines and the challenge of Low Speed Pre-Ignition (#LSPI). Learn about the rise of thinner oils for improved fuel efficiency and how they address the challenges of LSPI caused by higher operating temperatures. Discover the importance of using the correct oil specification for your vehicle, whether it's the latest ILSAC GF-5, GF-6, or GM DEXOS1 Gen3, to ensure optimal engine protection. Remember, the "old school" approach of using one oil for all engines isn't ideal.

Understanding Air Suspension

We explore the evolution and functionality of air suspension systems for vehicles.

Suspension Bushings: Role, Materials, and Wear Indicators

Regular inspection and timely replacement of worn bushings are crucial for optimal vehicle performance and safety.

Randy Breaux, Group President, GPC North America, Talks to AMN Drivetime

At NAPA, “Breaux Knows” business relationships, ABCs to avoid, and serving the automotive professional.

Serpentine Belt and Drive System Maintenance

Properly maintaining the entire drive system prevents premature belt wear and system failure, ensuring customer satisfaction and vehicle reliability.

Other Posts
High-Pressure GDI Fuel Pumps

When solving a fuel pump issue, the scan tool is your best friend.

EGR Systems: Understanding Exhaust Gas Recirculation

Learn how it works, its history, and its impact on both performance and the environment.

Advanced Cooling System Technologies: Hybrid & EVs

Learn how to keep your hybrid or electric vehicle running smoothly and efficiently.

Do EVs Require Special Brake Pads?

Proper brake pad selection is crucial for EVs to ensure consistent stopping power and long pad life.