Brake Job: 2006-2014 Honda Ridgeline

Brake Job: 2006-2014 Honda Ridgeline

Honda Ridgeline brake service issues are often related to the parking brake and hydraulics.

You might assume that the Honda Ridgeline shares a lot of the same components as the Pilot. Aside from the general proportions, the Ridgeline is a different vehicle made in a different plant. The brakes on the Ridgeline are robust and have very few problems with noise or pulsation. Where the service issues can be found are with the parking brake and hydraulics.

PARKING BRAKES
The parking brake on the Ridgeline is actuated using a pedal. The cable goes from the pedal to the equalizer bar that is mounted near the driver’s-side doorsill. Two cables come out near the fuel tank and the EVAP canister.

The parking brake is a drum-in-hat design that can be adjusted through a hole in the hat of the rotor.

Press the parking brake pedal with 66 lbs. of force to fully apply the parking brake. The parking brake pedal should be locked within 10 to 12 clicks.

Minor parking brake pedal adjustments (1 to 2 clicks) can be made with the adjusting nut on the pedal. To perform the adjustment, lift the vehicle. Release the pedal and press the pedal one click. Tighten the parking brake adjusting nut until the parking brake drags slightly when the rear wheels are turned. Release the parking brake pedal fully, and check that it does not drag when the rear wheels are turned. Readjust if necessary.

If a larger adjustment is required, perform a major adjustment using the adjuster nut at the parking brake drum. Remove the access plug in the rotor. Turn the ratchet teeth on the adjuster nut with a flat-tip screwdriver until the shoes lock against the parking brake drum. Then, back off the adjuster 10 clicks and install the access plug.

BRAKE BOOSTER AND MASTER
One of the more common complaints is brake pedal feel. To test the master cylinder, with the ignition switch in LOCK, depress the brake pedal several times to deplete the vacuum reservoir, then depress the brake pedal hard and hold it for 15 seconds. If the brake pedal sinks, either the master cylinder is bypassing internally or the brake system is leaking. Inspect the brake hoses and lines.

To test the brake booster, start the engine with the brake pedal depressed. If the brake pedal sinks slightly, the vacuum booster is operating normally. If the brake pedal height does not vary, perform the brake system test to see if the master cylinder is the problem. Depress the brake pedal with the engine running, and then turn the ignition switch to LOCK. The brake pedal height should not vary while depressed for 30 seconds.

If the pedal rises, start the engine and let it idle for 30 seconds. Turn the ignition switch to LOCK, and wait 30 seconds. Depress the brake pedal several times using normal pressure. When the pedal is first depressed, it should be low. On consecutive applications, the pedal height should gradually rise. This is normal.

If the pedal does not rise, inspect the check valve that is built into the vacuum hose going from the engine to the booster. With the engine running, pull the hose at the booster to confirm vacuum. If the check valve is faulty, replace the brake booster vacuum hose/check valve as an assembly. If the check valve is working and the brake pedal does not rise after several applications, it could be that the booster or the master cylinder are leaking internally.

ABS ASSIST
The Ridgeline has electronic brake distribution and brake assist. The brake assist system helps ensure that any driver can achieve the full braking potential of the vehicle by increasing brake system pressure in a panic situation, bringing the vehicle into a full ABS stop.

If during a panic stop the VSA modulator-control unit determines that the brake system pressure increases above a threshold in less than a certain amount of time, the VSA modulator-control unit engages brake assist.

Because the brake system pressure crossed the pressure threshold before the time threshold had expired, the VSA modulator-control unit goes into brake assist mode.

When a brake assist event occurs on the Ridgeline, the customer may notice a change in the brake pedal height, such that the pedal may drop a little bit. They should not be alarmed; this is a normal occurrence.

Article courtesy ImportCar magazine.

You May Also Like

Air Ride Conversion Kits

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring.

Article courtesy Brake & Front End.

Air ride, active dampening and other ride control technologies probably hit their apex of development in the past 15 years. Many of these vehicles have racked up the miles since then and now need to be repaired.

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring. The dampener will lose its ability to control the suspension’s movement due to internal wear and lose fluid inside the dampener.

Wheel Speed Sensors and Bearings

The only way to diagnose the sensor and circuit is with a scan tool or scope. 

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

Check TPMS, Save on Fuel for Your Next Road Trip

Discover the benefits of TPMS for enhancing safety, fuel efficiency and peace of mind during long road trips.

Brake Pad Errors and Mismatches

In order to make the right selection, you must do your homework while still remaining skeptical.

Other Posts

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.

Ball Joint Inspection

It’s important to remember not to miss a worn joint. If a ball joint fails, the driver loses control of the vehicle.

Brake Pad Edge Codes – What Can They Tell You?

The “Edge Code” can tell you information about a brake pad’s friction material.

Steering Angle Sensor Service

Ninety percent of the time when a steering angle sensor code is active, it means the sensor needs to be calibrated.