Cranky Crankshaft Seals -

Cranky Crankshaft Seals

Sometimes the least expensive parts are the most time-consuming to replace. This is the case with crankshaft oil seals.

Sometimes the least expensive parts are the most time-consuming to replace. This is the case with crankshaft oil seals. If a front seal has left a trail of oil for you to ponder, the repair is relatively minimal. But if the rear main seal is no longer doing its duty to keep the oil inside and dirt outside the engine, then you better tighten your belt because you’ll be logging some serious labor hours to replace a part that costs less than a meal at a casual restaurant.

Before assuming the leak is isolated to only the main seal, it is important to check other possible causes and make necessary repairs before replacing the seal alone. An installation error may be to blame if, for example, the seal was installed with the lip out instead of being oriented toward the inside of the engine. Run some fluorescent dye through the oiling system to be sure exactly where the leaks are coming from before you dig in.

There are a few possible causes of main seal leaks that you can confirm without dropping the transmission. What may look like a main seal leak may be from a cover, gasket, oil pan, oil cooler or even rear mounted oil sending unit. Oil that leaks from one of these senders can give the appearance of a rear main seal leak as it drips down the back of the engine.

Types of Seals

In older model vehicles, oil seals are two-piece designs. But GM changed the design in the mid-’80s to a one-piece design to reduce the chance of a misassembled seal on the assembly line. Two-piece conversion kits are available in the aftermarket, and many racers use them since they are easier to replace. If installed correctly, seals rarely leak. However, one-piece rubber or silicone seals are found on the majority of the vehicles on the road today. Some of these seals use a Teflon coated lip that transfers some material to the surface to provide lubrication and better sealing. For these types of seals it is best to install dry or a leak will develop if you use any lubricant. Installation of seals should be done with a proper tool that drives the part in evenly and doesn’t destroy the edges. It should be noted that some new seals are supplied with an alignment sleeve.


The positive crankcase ventilation system (PCV) can cause all kinds of trouble if it is not operating correctly. Clogged or broken vacuum lines, torn oil separator diaphragms, can produce carbon buildup and oil blowby that creates higher pressures resulting in oil leaks. For turbocharged and supercharged applications, crankcase pressures may increase exponentially if the PCV system is restricted. Lack of regular maintenance is often the culprit with the PCV because after time oil breaks down and will begin to sludge. The first effects of this usually show up as a misfire due to carbon build up or a clogged vacuum line.

Crankshaft Irregularities

A bent crankshaft will cause a lot more problems than a leaking oil seal, but if there’s even a slight amount of runout or flex due to not enough support from the main bearings, there could be trouble with the oil seals. The lip on the inside of the seal clamps down on the surface of the crank (front and rear) to provide enough force to keep oil from escaping and dirt from entering. Pressure from the crankcase pushes the lip outward against the surface of the flange to prevent leaks.

Some seals have a spring inside the lip to help seal it on the crank. If the lip moves too much or exposes the spring, it can score the crank sealing surface, causing a leak. Look for any burrs or grooves on the front and rear of the crankshaft to make sure it is smooth. Any sharp edges or gouges could damage the lip of the seal, allowing oil, dirt, and debris past. Larger particles can grind on the surface that may require further steps to bring it back to specification. You can use a piece of emery cloth to polish the crankshaft and clean it with carburetor cleaner or something that won’t react to silicone rubber.

Crankshaft Sleeve

If the output flange of the crankshaft is scored and damaged to the point where polishing won’t bring it back to life, some aftermarket companies offer crankshaft sleeves that fit over the flange between the seal and crank surface. Repair sleeves are not only available for the crankshaft sealing surface sleeves, but also for the harmonic balancer seal surface, and camshaft seal surfaces that can be installed with specialized tools to make placement as simple as possible.

Another point to look out for is the pilot bearing. Be sure to inspect the input shaft for misalignment because it can put stress on the crank and eventually lead to a leak and bearing wear. The crankshaft needs to ride on a smooth, flat surface on a thin film of oil. Your customer may need more than an oil seal if the crankshaft has worn the bearings or has low oil pressure. Be sure to check out all the potential causes for a leak before starting into a job this big.

Article courtesy Underhood Service.

You May Also Like

BMW Telematics – Has It Really Been 25 Years?

The first step into the connected future took place in 1998 with “BMW Telematics” and the BMW Assist package.

BMW has already put more than 14 million telematic-equipped vehicles on the world’s roads over the past quarter-century. Currently, BMW has more than 2.3 million subscribers worldwide. As time has passed, the connection has changed how many functions on a BMW operate.

The first major foray into the connected future took place in 1998 with “BMW Telematics” and the introduction of the BMW Assist package comprising concierge services, traffic information and intelligent emergency call. BMW claimed that if your airbags went off, your call would be placed first in line when connecting to the police. At that time, the analog telephone was still used for establishing an online connection. Unfortunately, all of these vehicles had an analog cellular phone connection until analog cellular providers phased out analog services in 2008.

SkillsUSA Names First Competitor for WorldSkills 2024

Lily Williams of Jonesboro, AR, named as the official competitor for Car Painting at the 2024 WorldSkills Competition.

Crankshaft Counterweights And Balancing

Imbalance in the engine exhibits vibration and damage. Balancing becomes critical to any engine build.

Check TPMS, Save on Fuel for Your Next Road Trip

Discover the benefits of TPMS for enhancing safety, fuel efficiency and peace of mind during long road trips.

The Impact of Fuel Type on Engine Performance

When choosing the right fuel, consider engine design, manufacturer recommendations and intended usage.

Other Posts

Grinding/Rubbing Noise While Braking At Or Below 10 MPH

Some 2020-2023 Escape hybrid vehicles may exhibit a grinding or rubbing noise while braking at or below 10 mph.

Acura Frozen Starter Causes No Start

Why won’t the engine crank after the vehicle has been exposed to precipitation and then freezing temperatures?

Fine-Tuning Your Wheel Balancing Process

The first step to a smooth ride and well-balanced tire has nothing to do with the balancer.

Drilled and Slotted Rotors

There’s real science behind the location of holes, slots and grooves in today’s brake rotors. Plus, they look great too.