Diagnosing Intake Manifold Failures -

Diagnosing Intake Manifold Failures

Many owners of late-model Mercedes-Benz cars equipped with 3.0L and 3.5L V6 engines (M272 or M273) have experienced performance problems that include poor idle, loss of power and a check engine light with a P2006 code (or sometimes other codes).

Many owners of late-model Mercedes-Benz cars equipped with 3.0L and 3.5L V6 engines (M272 or M273) have experienced performance problems that include poor idle, loss of power and a check engine light with a P2006 code (or sometimes other codes).

The problem is caused by an adjustable air flap (also known as a runner or swirl flap) inside the intake manifold that breaks, resulting in unexpected and deficient performance depending on the orientation of the broken flap. These flaps move and alter the length of the intake manifold runners.

We have seen several of these intake manifold failures lately at the shop caused by the air flap that Mercedes-Benz calls a resonance manifold. As you know, the primary job of the intake manifold is to evenly distribute the combustion mixture (or the air in a direct-injection engine) to each intake port in
the cylinder head(s). Even distribution is important to optimize the efficiency and performance of the engine.

Image 1

In our example, we have a 2006 Mercedes-Benz CLK 350 (272.9 engine) with a check engine light on for multiple misfires. We have seen O2 codes as well as lean codes, so be sure to test your system correctly. Once you have completed this step, it is time to look at the manifold, paying special attention to two areas on the front of the intake. The first one is obvious. There is a lever that connects the outside runners to the center actuator (see Image 1, red outline area).

The area that is not so obvious involves the actual shafts inside the manifold (see Image 2). The shafts will fail inside the manifold and bind, causing the lever to break and the caps shown to look like they are popping off the manifold. Do not be fooled by aftermarket repair kits; they are ineffective at repairing the shafts on the inside. In the shop we have seen cases where parts of the flap became dislodged and ended up in the engine. When this happens, the technician will need to do a valve job to repair the vehicle.

Image 2

Digging In

The repair process is pretty straightforward. First, go to the engine control unit (ME-SFI) located on top of the engine, (see Image 3, N3/10). Exercise care when removing and installing the electrical connectors, and keep them safe too — they are expensive and vehicle specific.

You won’t need any special tools, so you can just get started. However, there will be hoses and seals you’ll want to order before doing the job. Over time, they get brittle and won’t be serviceable if you can get them off in one piece.

Disconnect the electrical connectors, fuel lines, air filter housing and mass air meter. I’m sure you have heard this before, but make sure nothing falls into the engine when the manifold is removed. Follow the factory instructions found in your service information system. If you follow all the steps carefully, the repair will go smoothly. Just take your time, verify the repair with a good drive cycle, and you will have properly repaired the intake manifold issue on your customer’s Mercedes-Benz.

Image 3: Courtesy of ALLDATA

 

Why Are Variable-Length Runner Intake Manifolds Popular?

A variable-length intake runner manifold can switch between two sets of intake runners with a flap built into the manifold. This way, there is one set of intake runners that is optimized for when the vehicle is idling and picking up low-rpm speed. Then, if the driver gets on the throttle and requests power for more demanding driving, the flap switches over to the second set of intake runners that is optimized for the higher-rpm range. Many of these intakes also have specifically shaped flaps that cause a vortex, adding even more efficiency.

The most common part to fail on the Mercedes manifold is one of the actuators for the variable system, causing the interior flap to become disconnected.

Article courtesy Import Car.

You May Also Like

Updating Your TPMS Tools Regularly Matters

You can ensure your read is accurate by updating your tool regularly.

Courtesy of Tire Review by Yanick Leduc

Picture this: Mark, an experienced tire service technician, is on the phone with a technical support representative from his TPMS supplier, inquiring why his new sensors don’t seem to work properly with the 2019 Silverado he’s servicing.

Mark: “The truck doesn’t seem to pick up the signal from the new sensor!”

Cabin Air Filters

Cabin air filters will protect the health and well-being of the driver and passengers.

Diagnostic Procedures For Stop/Start Systems

Stop/start technology is more than just a switch wired to the brake pedal and starter.

Brake Pad Wear Sensors

Brake pad wear sensors have been around for years and continue to evolve.

Topology and Your Scan Tool

Topology influences how you access the modules with your scan tool.

Other Posts

Ride Control Diagnostics From Tire Wear Clues

Learning how to read the tire and communicate your findings is the key to ride control service.

Understanding Engine Timing- Chains, Gears and Belts

Engine timing is critical for overall performance.

Air Filters and Fuel Trims

Modern engines rely on precise airflow and oxygen sensor data for optimal performance.

Mercedes Ignition Coil Pack Diagnostics

Replacing a single coil might not be the best approach to curing an engine of a chronic misfire.