How Well Do You Know Your Driveshaft?

How Well Do You Know Your Driveshaft?

There are three types of modern driveshafts with multiple configurations.

What are the different driveshaft configurations?

• Single shaft with two Cardan universal joints;

• Single shaft with double Cardan on one end and one Cardan on the other end; or

• Split shaft with three Cardan and center carrier.

The world’s longest one-piece light truck propshaft, brought about by a team of engineers from General Motors, Dana Corp, and Alcoa. Looking for a way to improve NVH on the Chevrolet Silverado and GMC Sierra Heavy-Duty extended cab longbox pick-ups, engineers found the solution by replacing the two-piece steel design with a one-piece aluminum driveline. The team’s challenge was to develop a one-piece aluminum propshaft with specifications previously unattainable in the light truck industry.

On 4WD vehicles, you can have these configurations:

• Front driveshaft with two Cardan universal joints;

• Front shaft with double Cardan on one end and single Cardan on the other end;

• Older 4WD outer half shafts with Cardan universal joints; and

• Newer 4WD with boot-covered constant velocity joints.

Why are some driveshafts two pieces?

It comes down to harmonics. A large single piece driveshaft has a natural frequency within the range of human hearing. A two-piece driveshaft breaks up that harmonic.

Why do center support bearings fail?

Premature failure of the center bearing could be the result of too much driveshaft angle, the water shield being missing or damaged, road salt and moisture, or damaged rubber casings. Also, high mileage and bearing wear can contribute to premature wear.

What are the symptoms of a failed joint?

There are different things to look for when you suspect universal joint problems:

• The cling and crunch sound when going from drive to reverse with the brake on;

• Rust-colored dust around the universal joint itself;

• With driveshaft removed, any binding in the movement of the universal joint; and

• Vibration on takeoff and vibration on torque.

What is phasing?

Phasing is the proper alignment of the inboard yokes.

The first thing to do after the vehicle has been hoisted and the driveshaft has been removed is to mark the yokes for correct phasing. If you are working with a split shaft, make sure to mark the shaft before splitting it. 

How should a a driveshaft be secured in a vise?

Make sure to clamp around the yoke and not on the hollow tube itself. This eliminates the chance of the hollow tube being damaged if clamped too hard. The best way to remove an old universal joint is to use the proper tools. If the shaft is dented it should be replaced because the outer shaft carries the loads.

What conditions should be replicated for drivetrain noise on 4WD vehicles?

Driveline noises caused by loading in 4WD vehicles may be mistaken for transfer case or front axle noise because they can sound very similar. 4WD noise caused by loading may exhibit the following conditions:

• The noise will be greatest on a clear, dry road and decrease on a low-traction surface. Front axle or transfer case noise caused by a bearing, ring and pinion, or planetary gearing will be the same on all surfaces;

4MATIC: Der intelligente Allradantrieb 4MATIC: the intelligent all-wheel drive system

• The noise will increase while making a tight turn. Most front axle or transfer case noises won’t increase;

• The noise can be changed from a deceleration condition to acceleration (or acceleration to deceleration) by raising or lowering tire pressure at one end of the vehicle; or

• One or more of the tires may show small, short scratches around the circumference of the tire tread. These scratches are caused by the tire slipping, or “scuffing,” on the road surface.

Article courtesy Brake & Front End.

You May Also Like

Air Ride Conversion Kits

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring.

Article courtesy Brake & Front End.

Air ride, active dampening and other ride control technologies probably hit their apex of development in the past 15 years. Many of these vehicles have racked up the miles since then and now need to be repaired.

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring. The dampener will lose its ability to control the suspension’s movement due to internal wear and lose fluid inside the dampener.

Wheel Speed Sensors and Bearings

The only way to diagnose the sensor and circuit is with a scan tool or scope. 

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

Check TPMS, Save on Fuel for Your Next Road Trip

Discover the benefits of TPMS for enhancing safety, fuel efficiency and peace of mind during long road trips.

Brake Pad Errors and Mismatches

In order to make the right selection, you must do your homework while still remaining skeptical.

Other Posts

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.

Ball Joint Inspection

It’s important to remember not to miss a worn joint. If a ball joint fails, the driver loses control of the vehicle.

Brake Pad Edge Codes – What Can They Tell You?

The “Edge Code” can tell you information about a brake pad’s friction material.

Steering Angle Sensor Service

Ninety percent of the time when a steering angle sensor code is active, it means the sensor needs to be calibrated.