Live-Axle Wheel Bearing Replacement

Live-Axle Wheel Bearing Replacement

Replacing wheel bearings on a vehicle with a live rear axle may not be one of the most frequent jobs, but it can be one of the most profitable. While the basics have not changed in more than 60 years, new seal materials and differential designs have added new wrinkles.

2015 GMC Canyon Automatic Locking Rear Differential
Replacing wheel bearings on a vehicle with a live rear axle may not be one of the most frequent jobs, but it can be one of the most profitable. While the basics have not changed in more than 60 years, new seal materials and differential designs have added new wrinkles.

Bearings

Replacing rear wheel bearings on a live-axle rear suspension requires a few extra steps when compared to a unitized bearing. To remove the axle shaft, the differential must be accessed and the clips that hold the axle in the differential must be removed.

There are three bearing styles — Conrad, roller and ball. Most axles use these types of bearings in a cartridge-type arrangement. They are installed into the axle ends or pressed onto the shaft and possibly held in place with a pressed-on retainer. On some axles, the bore on the housing is tapered and the bearing will fit in only one direction. This is where measuring tools can save you time and maybe multiple part deliveries.

Some axles use a “floating” axle shaft design. This design takes the weight of the vehicle off the axle so all it has to do is transmit power. This allows the hub of the axle to carry a greater load. Some of these axles use tapered roller bearings. Another advantage of a floating axle is if the axle separates from the differential or flange, the wheel will not fall off the axle.

The most critical part of the disassembly is removing the bearing and retainer from the shaft without damaging the axle shaft or housing. Any damage to the surfaces that the seal or bearing rides on can cause a premature failure of the new bearing.

Another rookie mistake made by some technicians is installing the parts in the wrong order. It is not uncommon to press the new bearing onto the axle only to realize the flange plate was not installed.

Look at the differential cover before you quote the job. On snow-belt vehicles, the differential cover is prone to rust. Perforation does happen, but chances are prying on the weakened cover may distort it to the point that it will never seal. Replacement covers are readily available and very economical.

Seals

The main killer of solid axle wheel bearings is a failed seal. Most seals ride on the axle shaft, and they typically have a lip and a spring that holds the lip to the axle. When a seal is installed, take your time installing the axle. Splines can damage the seal and cause leaks.

The area on the axle shaft where the seal and bearings make contact is the most important. It must be free of rust and imperfections. Use only a fine-grade emery paper to clean the axle shaft between the flange and the worn area.

If the surface is grooved or damaged, the axle can be repaired with a sleeve on some applications. If not, the axle should be replaced. Another option for some applications is to install a replacement bearing that repositions the bearing and seal to ride on unworn surfaces.

Make sure the seal is installed in the correct position. A correctly installed bearing may extend out from the housing up to 1/4”. Some axles have small seals that must be positioned properly so pressures can be relieved and the lip can work.

Make sure the breathers on the axle are not clogged. The breather on some axles acts as a PCV valve to keep pressures within a certain range so the seals can work their best as the differential heats and cools. If a breather is clogged, the heat will increase pressure in the axle. As the axle cools, a negative pressure could build up behind the seal. These changes in pressure will cause the lips of the seals to deform and leak.

Any leak on an axle should be taken seriously. Ignoring a leak can be very expensive and destroy the bearings, brakes and differential.

You May Also Like

Audi Active Suspension Service

The key to servicing these systems is proper information and understanding precisely how these systems operate.

Audi active shocks and struts usually go unnoticed, until there is a problem or when a message is sent to the instrument cluster indicating there is a fault with the system. Swapping parts on these systems and using guesswork to diagnose a problem will usually result in an angry customer and an annoyed parts supplier. The key to servicing these systems is proper information and understanding precisely how these systems operate.

Power Steering Pull

Every driver has a different threshold for a pull.

Manual Clutch Repair and Diagnostics

If the clutch gets too hot from excessive slippage or loading, the linings may burn, damaging the clutch.

ADAS Calibration

Accuracy is important for sophisticated ADAS systems.

AWD and ABS Services

AWD is always engaged and with the ABS brake modulator, can perform like systems with limited-slip differentials.

Other Posts

Testing A/C Or Heater Blower Motor Circuits

The heat eventually burns out the blower motor resistor, and, in many cases, causes the electrical connector to melt.

Spark Plug Replacement

Here are some tips to follow when replacing a spark plug.

Installing New Rotors

Knowing if and why there’s runout will help you reinstall a smooth braking system.

Oxygen Sensors And Catalyst Efficiency

Newer air/fuel ratio or wide-band sensors can detect a wide range of fuel conditions.