Top 5 Spark Plug Tips -

Top 5 Spark Plug Tips

Here are 5 little-known tips about spark plug replacement that you might not learn in the classroom.

Here are 5 little-known tips about spark plug replacement that you might not learn in the classroom.

1. Getting Plugs Out: Chemical Tools

If a spark plug is difficult to remove, some fluids can help break up corrosion and carbon between the threads on the plug and head. You can pour a liquid penetrant into the wells and let it sit for an hour or longer. Some technicians have had luck with an in-tank fuel injector cleaner to help break up the carbon that forms between the plug and the head, like that which occurs on Ford modular V8s. The key with this method is time; the longer the fluid is in the well, the better the penetration.

If you have a spark plug that feels notchy, the fluid method can prevent damage to the threads. Just crack the plugs a quarter turn and pour in a penetrant or fuel injector cleaner. If you used a lot of fluid, you might need to change the oil after the plugs are replaced.

2. Spark Plug Hole Hygiene

The spark plug well or tube should be free of oil, water and debris. Removal of the spark plug can be difficult, if anything exists in the tube or well. Over time, debris and fluid can help to create a path to ground because the secondary ignition creates static electricity that attracts small particles to the insulator. If you see oil or other debris in the spark plug tube or well, replacing the valve cover gasket or the boot on the coil can prevent a misfire in the future.

3. Engine Temperature Removal

A controversial topic among technicians and engineers is whether the engine should be hot or cold when replacing the spark plugs. The OEMs and spark plug manufacturers always recommend removing and installing the plugs when the engine is cold. The reasoning is that this is when the spark plug and head have the least amount of thermal expansion and the chances of damage to the threads. This is critical when you consider that the head might be aluminum and the plug is steel.

Believers in the “removing when hot method” can’t really explain why it works. Some say it loosens up the galling and corrosion between the threads of the plug and the head. Some of them even insist that the use of an impact can help break the plug loose. If it works for you, go with the hot method. Just make sure you have all of the tools to repair the threads and install inserts.

4. Coil Bolts

Always apply the specified torque to the specified mounting thru-bolt for the coil. Loose thru-bolts could lead to failures under vibration. Over tightened thru-bolts could lead to a cracked coil mounting ear and/or premature thru-bolt failure. Not getting it right can lead to a diagnostic nightmare.


5. Under or Over Torqued

Most articles will tell you to use a torque wrench, but they never explain why. The real reason involves heat transfer. An under-torqued spark plug will not make full contact with the cylinder head. This reduces a plug’s ability to transfer heat and will result in elevated combustion chamber temperatures. This can cause pre-ignition and detonation and lead to engine damage. An over-torqued spark plug can cause stress to the metal shell, leading to thread damage or breakage. Also, excess tightening can compromise a plug’s internal gas seal or even cause a hairline fracture to the insulator.

Article courtesy Underhood Service.

You May Also Like

Ball Joint Inspection

It’s important to remember not to miss a worn joint. If a ball joint fails, the driver loses control of the vehicle.

Don’t miss a worn joint!

Detecting and measuring wear in a ball joint is critical to ensuring the safety of a vehicle. 

Types of Ball Joints

A ball joint is made up of a housing, ball stud, bearings, end cover and Belleville washer or spring. A Belleville washer is a conical-shaped spring designed to be loaded in the axial direction. The joint is attached to a control arm by pressing or riveting the joint into the arm. If the joint is pressed into the arm, it will require a special tool to remove the old joint and install the new one. 

Electronic Throttle Body Service

On most systems, idle speed is completely controlled by the throttle plate angle.

Spark Plug Replacement

Here are some tips to follow when replacing a spark plug.

Transmission Fluid Hydraulics

You need to know how transmission fluid flows inside an automatic transmission.

How ADAS Systems Perform

When new technologies are applied to driver safety, a higher level of scrutiny and service is required.

Other Posts
Air Ride Suspension Diagnostics

The key to understanding the embedded logic of air ride systems is using service information.

Steering Angle Sensor 101

The steering angle is used by many ADAS functions.

BMW N54 Turbo Problems

Here are some common problems or failures that you should be on the lookout for.

Mercedes-Benz Engine Oil Leaks

Mercedes makes a fine product, but certain repairs will emerge as trends over time.