TPMS Curve Balls

TPMS Curve Balls

You may think you know the cause of a TPMS problem, until one car defies it.

When you think you know everything about tire pressure monitoring systems (TPMS), there will be a car or truck that pulls into your bays and challenges all of your knowledge and diagnostic skills. It may not be a case of a mouse chewing a wire or poorly installed accessory – it is how the manufacturer engineered the system.

Measuring the pressure inside a tire directly or indirectly is the easy part. Being able to turn a light on in the dash if a tire is low leaves engineers with a lot of different ways to accomplish the task. 

Direct Or Indirect

You would think you could simply classify TPMS Systems into two distinct categories of direct and indirect vehicles. Direct TPMS directly measure tire pressure and temperature with a sensor. Indirect systems use wheel speed sensors to measure the pressure indirectly.

But, there is a third type of system. BMW and Mercedes-Benz both use direct sensors in the tires but also look at wheel speed sensor data as part of a flat tire detection system. The combined system can detect a blowout faster.

Antennas

On most vehicles, there a single antenna for the four sensors. The antenna may be only for the sensors, or it could also be used for the keyless entry system. Why? The keyless entry system and TPMS sensors both transmit in the same radio frequency range of 315- to 430Hz. 

Some vehicles have a dedicated module and antenna(s). Some vehicles have four antennas on the vehicle in the wheel wells. Some Chrysler systems have three dedicated antennas with the ignition switch module antenna acting as the fourth antenna. You probably won’t know until you pull up the wiring diagram.

The signal from a TPMS sensor or key fob is a one-way conversation on most vehicles. The keyless entry fob or TPMS sensor transmits and the vehicle receives. Yes, some aftermarket replacement sensors and key fobs can be programmed wirelessly, but this is a different set of signals and antennas. 

When a TPMS sensor or key fob transmits, it is a very dull but fast (and important) conversation. It typically starts with an identification number that tells the module connected to the antenna to listen up. This code says the sensor or fob belongs to the vehicle. The next part of the transmission contains a command or status update on the tire pressure and temperature. 

Just when you thought sensors do not receive signals, you find a system that has transmitters in the wheel wells. Instead of waiting for the sensor to transmit on its own, a transmitter in the wheel well will send a signal to a sensor at around 125Hz. The signal tells the sensor to transmit a signal. The main advantage of this type of system is the individual pressures can be obtained when the vehicle is stationary. 

While this type of knowledge is not required to determine if a sensor is not functioning, it might prove to be essential when diagnosing a problem where data from one corner is not making it to the module.

TPMS Mapping, Modules And The Light

Once the antennas, sensors or wheel speed sensors have detected a low-tire condition, it has to be communicated to the driver. This is done with a light in the dash and/or a message in the driver information display. The information can take several routes and pass through different modules.

Most TPMS systems have the antenna connected to the keyless entry module. Some systems have a dedicated TPMS module. But, the command to turn on the light may go through a body control module. Some vehicles have TPMS modules that communicate on a serial data bus with the instrument cluster or combination meter module.

But then an automaker can throw you a curveball. Some early systems have the TPMS lights in the instrument cluster that are directly wired to the module. 

Finding how the sensors communicate with the light is a critical step for situations where the system is not functioning or is causing DTC in other modules. Sometimes the root cause of a TPMS problem is not the TPMS module or sensors, but it could be the network or the modules on the network.

Diagnostic Path

I believe in the “Test Before You Touch” method as a way to perform triage when assessing the initial customer complaint. This procedure can rule out inflation and dead sensor problems. But if the problem can’t be resolved, it requires looking at the service information and technical service bulletins (TSBs). 

Your TPMS tool is not just for relearns and programming sensors. Many of these tools can pull codes from the TPMS module through the OBDII connection. Also, they can be used to detect and measure the strengths of radio signals coming from sensors and the environment around the car. 

Many TPMS systems are more than a decade old. With older vehicles, there are more curveballs. During the first years of the TPMS mandate in 2007 and 2008, many manufacturers were still trying to integrate TPMS sensors, antennas and modules onto pre-existing platforms. These single-model exceptions are where you might have to be a diagnostic switch hitter. Never assume that all TPMS systems operate the same way.

You May Also Like

Wheel Speed Sensors and Bearings

The only way to diagnose the sensor and circuit is with a scan tool or scope. 

When wheel speed sensors (WSS) were first installed on cars and trucks, they were typically mounted on the CV joints or differentials. These sensors were not the most accurate and didn’t start working until the vehicle reached 5 to 7 mph. These are called passive wheel speed sensors. 

As vehicles and ABS systems advanced, the wheel speed sensors moved to the knuckles and wheel bearings. These advanced sensors can detect small amounts of movement in the wheels when the vehicle is barely moving. They are called active sensors. But, with active sensors, the inspection and diagnostic process is more challenging. Why? Because the encoder ring is moved to the wheel bearing inboard seal, and the sensor is moved to the knuckle. The only way to diagnose the sensor and circuit is with a scan tool or scope. 

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

Check TPMS, Save on Fuel for Your Next Road Trip

Discover the benefits of TPMS for enhancing safety, fuel efficiency and peace of mind during long road trips.

Brake Pad Errors and Mismatches

In order to make the right selection, you must do your homework while still remaining skeptical.

Chassis Parts and Alignment Angles

Knowing why the adjustment is required is critical to performing the total alignment.

Other Posts

Ball Joint Inspection

It’s important to remember not to miss a worn joint. If a ball joint fails, the driver loses control of the vehicle.

Brake Pad Edge Codes – What Can They Tell You?

The “Edge Code” can tell you information about a brake pad’s friction material.

Steering Angle Sensor Service

Ninety percent of the time when a steering angle sensor code is active, it means the sensor needs to be calibrated.

Wheel Bearing Service Tips

When faced with any noise complaint, take the time to test-drive the car.