Undercover: Double Down — The Advantages of Twin-Tube Shocks -

Undercover: Double Down — The Advantages of Twin-Tube Shocks

Twin-tube shocks and struts have been used as original equipment on most vehicles for many years.

Twin-tube shocks and struts have been used as original equipment on most vehicles for many years.  But in recent years, we’ve also seen more monotube shocks and struts being used as original equipment dampers on sports and performance vehicles.  So what’s the difference and what are the advantages and disadvantages of each design? Read on and we’ll take a look at twin-tube shocks and struts to better understand how these ride control products evolved and how they work.

The Early Years
As vehicles became capable of faster speeds, the first add-on “friction dampers” appeared. These primitive shock absorbers had two arms connected at a pivot point with metal and leather washers at the elbow. One arm was connected to the axle and the other arm to the frame.  When the suspension moved up and down, the leather and metal washers at the elbow rubbed against each other to create friction and dampen the motion. An adjustment bolt at the elbow could be tightened or loosened to modify the amount of friction or dampening provided by the unit.

The first telescoping hydraulic shock was invented in 1901 by C. L. Horock, according to the Bosch Book of The Motor Car.  This was the predecessor of the modern shock absorbed because it used a piston in a fluid-filled cylinder.  The shock featured an adjustable bleed hole and valving between the ends of the cylinder to control fluid movement and dampening action.  The piston also had a one-way valve that allowed the shock to compress with little resistance to absorb bumps, then to offer greater resistance on rebound to dampen the suspension.  This was a major improvement over friction shocks because it allowed variable two-way dampening between compression and rebound.

The telescopic design was also compact and direct acting.  There was no arm to deflect or bend or break, and the force generated by the motions of the suspension traveled directly down the center of the shock. It was also a simple design that was economical to manufacture.

During these early years of automotive history, “hybrid” shocks (see the diagram  to the right) appeared, They combined elements of the earlier friction shocks with hydraulic dampening. Most of these shocks had an arm that attached to the axle like a friction shock, but the pivot was connected to a pair of blocks or pistons in a housing that pumped hydraulic fluid back and forth to dampen the suspension.  Some of these early shocks were “single-acting” designs that only worked on rebound, while others were “double-acting” shocks that dampened the suspension during jounce and rebound. Though these designs were used on many cars in the 1920s, they proved to be an evolutionary dead end.

As vehicle technology evolved and suspensions designs moved away from solid front axles to control arms and independent suspensions, the telescopic hydraulic shock become the predominant damper.  

In 1932, the Hudson Motor Car Company was the first automaker to equip its cars with four direct-acting hydraulic shocks. Other automakers, such as Auburn, Reo, Chrysler, Packard and Terraplane, soon followed suit. In 1949, Ford changed to direct-acting hydraulic shocks, followed by Chevrolet in 1950.

Did You Know…
In 1906, a friction shock that used a special friction material (Ferodo) in the elbow joint was patented by E.V. Hartford, making Hartford shocks a popular design for more than 30 years. Later designs added a bowden cable so the shocks could be adjusted on the fly from the driver’s seat (making these the first “adjustable” shocks). 

Direct-Acting Shocks
Direct-acting hydraulic shocks became the norm because as vehicles became heavier, spring rates got softer. Motorists wanted a smoother ride with less bounce, so direct-acting shocks that provided variable dampening action both ways provided the answer that the public wanted.

In a twin-tube direct-acting shock, there is an inner tube for the piston cylinder, and an outer tube that serves as a fluid reservoir.  Valves in the piston and in the bottom of the shock control fluid flow in both directions and determine the dampening characteristics of the shock.

During the compression stroke when the piston moves down, some fluid flows through the piston valve from the lower chamber below the piston to the upper chamber above the piston. At the same time, some fluid in the lower chamber is also displaced through the valve in the bottom of the shock into the outer reservoir. If there were no valving in the piston or the bottom of the shock, the piston would hydrolock as if it had hit a solid wall because fluid is incompressible.

So the piston has to have orifices and/or some type of valving that allows the piston to move through the liquid. The valving at the bottom acts sort of like a safety valve and allows excess pressure in the lower chamber to vent into the reservoir when the vehicle hits a hard bump. The valve is usually velocity-sensing, which means it doesn’t open unless there is a sudden and sharp increase in pressure.

The valving at the bottom allows pressure in the lower chamber to vent into the reservoir when the vehicle hits a bump.

Piston size is also a factor.  The larger the bore size, the greater the volume of fluid that’s displaced with every stroke of the piston inside the shock — which provides greater dampening ability. Thus, heavy-duty shocks typically have larger bore diameters than standard shocks.

During the extension cycle when the suspension undergoes rebound and pulls the shock out, the upward movement of the piston generates pressure in the upper chamber as it pushes through the fluid. The piston also sucks fluid back into the lower chamber from the reservoir when the valving in the bottom of the shock opens.

By using “staged” valving, the rate at which fluid moves between the upper and lower chambers, and the lower chamber and the outer reservoir can be carefully controlled to modify the dampening characteristics of the shock. At low shock velocity, the valving can be set to allow easy movement between the chambers for a soft, boulevard-like ride.  As shock velocity increases, the valving can change to create more resistance and “stiffen” the shock for better ride control.

The valving can be designed to be equal in both directions (50/50 shocks), or much higher in one direction and lighter in the other (as in the 90/10 front shocks used in drag racing that extend easily to improve weight transfer to the rear wheels, but are slow to compress).

Shocks can also be calibrated so that they vent pressure and compress easily when hitting a bump, or vise versa.  The valving can also be made variable with a mechanical dial (adjustable shocks) or a solenoid that changes the valving (electronic shocks).  

Shock valving can also be modified by machining several small slits or grooves into the wall of the piston chamber.  These grooves are positioned in the middle area of the shock where the piston spends most of its time.

By allowing more fluid to bypass the piston, the grooves provide a smoother ride in the “comfort” zone.  But when the piston travels up or down beyond this range, it encounters more resistance and provides stiffer control.

Did You Know
Something else to keep in mind is that a shock absorber converts the energy of motion into heat. The faster a shock is pumped up and down, the more resistance it creates and the more heat it generates. The heat is dissipated into the fluid, the shock body and the surrounding air.  On a rough road, a shock can get pretty hot.  If the shock does not get adequate cooling, the oil can thin out and cause the shock to fade.

Shocking Concerns
If you’ve even seen a cutaway shock with a see-through glass or plastic piston chamber, you can see what happens to the fluid when the piston pumps up and down.  At relatively slow speed, the fluid just moves back and forth (not very interesting). But when you pump the shock up and down rapidly, air bubbles form behind the piston.

Engineers call this cavitation, and it causes aeration and fluid foaming. Fluid aeration and foaming is not a good thing inside a shock absorber because air is compressible and is much thinner than the liquid it displaces. Consequently, the shock starts to “fade” and provides much less resistance and ride control than it did before the fluid started to foam. On a rough road, this can cause a lot of tire bounce, loss of traction and even loss of handling control.

In 1956, a Frenchman named De Carbon found a solution for the foaming problem.  He discovered that pressurizing the fluid with nitrogen, Freon or air helped reduce foaming.  He took his idea to the German shock manufacturer Bilstein, and they patented a design for a single tube (monotube) shock with a high pressure (360 psi) gas charge in the bottom of the shock.  A floating piston separated the gas charge from the hydraulic fluid.

The original patent expired in 1971, and similar designs were soon developed by other companies.  Gas-pressurized monotube as well as twin-tube shocks soon became popular in the aftermarket for racing and performance applications.  

It wasn’t long before the automakers picked up on the new technology and began equipping their vehicles with gas shocks and struts as original equipment. In 1982, the first original equipment gas-charged twin-tube shocks were used on the Lincoln Continental. The first adjustable gas-pressurized shocks were introduced 1979.

Twin-Tube Advantage
One of the advantages of a twin-tube gas pressurized shock is that less gas pressure can be used to prevent the fluid from foaming.  Some twin-tube shocks contain as little as 35 psi, while others may contain as much as 100 to 150 psi.  This eliminates the need to have a highly polished piston bore with a floating piston (which lowers manufacturing costs), and it allows a softer ride for everyday driving.

The gas charge in the top of the outer fluid reservoir works like a pressure cooker to prevent foaming. This significantly improves ride control performance by reducing fade, noise and roughness.  It also allows more latitude in shock valving for a wider range of control compared to a conventional shock or strut.

The twin-tube shock is also less expensive to manufacture than a monotube shock because it does not require a high polished piston chamber, or a floating piston to separate the gas charge from the oil inside the shock.

You May Also Like

Bleeding the Brakes

It’s a simple concept, but not without the occasional headache.

Bleeding the brakes is a procedure that’s performed to remove air from the system when a component is replaced, and one that’s performed strictly from a maintenance standpoint of flushing or changing the brake fluid. The telltale symptom of air in a brake system is a soft or “spongy” pedal, along with poor brake performance.

Deciphering An Engine Misfire Code

When the fuel and air mixture ignites in the cylinder, many changing factors must be met to pass a misfire monitor.

AWD and ABS Services

AWD is always engaged and with the ABS brake modulator, can perform like systems with limited-slip differentials.

BMW Telematics – Has It Really Been 25 Years?

The first step into the connected future took place in 1998 with “BMW Telematics” and the BMW Assist package.

SkillsUSA Names First Competitor for WorldSkills 2024

Lily Williams of Jonesboro, AR, named as the official competitor for Car Painting at the 2024 WorldSkills Competition.

Other Posts

Aftermarket Leaders Honored with Northwood U Awards

The Automotive Aftermarket Management Education Award is given to education-minded industry leaders

Vehicle Repaired In Joe’s Garage To Be Donated

ASE-certified master technicians guided their teams during show hours, working alongside students.

Crankshaft Counterweights And Balancing

Imbalance in the engine exhibits vibration and damage. Balancing becomes critical to any engine build.

Check TPMS, Save on Fuel for Your Next Road Trip

Discover the benefits of TPMS for enhancing safety, fuel efficiency and peace of mind during long road trips.