Master Cylinders Leak

Undercover: Taking a ‘Brake’ To Examine Master Cylinders

Although modern master cylinders are reliable, they do require periodic inspection.

If nothing else, modern master cylinders are notable for their long and relatively trouble-free service lives. The modern master cylinder evolved from the single-piston types introduced in the 1930s, to the modern dual-piston, dual braking system cylinders in use today.

Master cylinders intended for drum brake use contain one or more residual pressure check valves that maintain a slight pressure in the system. This residual pressure applies tension to the wheel cylinder linkage in the drum brakes and keeps the wheel cylinder piston cups expanded against the cylinder bores.

During the 1980s, a quick take-up device was incorporated in some master cylinders to quickly take up the wide brake pad-to-brake rotor clearances existing on some braking systems.

photo 1: the compensation port is located directly ahead of the piston seal resting in the cylinder bore. the larger breather port is located directly after the piston seal.A Masterful Design
A master cylinder piston is designed to allow the driver to compensate for a low brake pedal by pumping the brake pedal.

The master cylinder bore incorporates a “breather” port located behind the piston cup, which allows brake fluid to flow into the cylinder as the brake pedal is depressed.

The fluid then flows around the piston seal into the cylinder as the pedal is released.

The cylinder also incorporates a “compensation” port (see Photo 1) that is located immediately ahead of the lip of each primary and secondary piston seal or cup.

The compensation port is designed to bleed air bubbles from the cylinder bore into the cylinder reservoir (see Photo 2).

When the brake pedal is applied, the compensation port is closed as the rubber cup travels past the port. Hydraulic pressure is then developed in the cylinder bore. Operating in tandem, the breather and compensation ports allow the driver to increase hydraulic pressure in the system by pumping the brake pedal.

photo 2: if the brake booster and brake pedal pushrods aren’t correctly adjusted, the compensation port will remain closed, which will cause the brakes to drag or lock up. inserting a small-diameter wire into the compensation port can test piston cup position. a better method is to hold a shop towel over the cylinder reservoir while a helper gently taps the brake pedal. each compensation port should spurt a small amount of fluid into the reservoir. Dual master cylinders are configured to operate two separate braking systems. The brake booster push rod engages the primary piston first.

The secondary piston is normally engaged by hydraulic pressure generated by the primary piston. In a conventional arrangement, the front and rear axles operate as two separate systems.

In a dual-diagonal system, the left front/right rear and right front/left rear brakes operate as separate systems. Dual diagonal systems usually provide better stopping power and steering control when hydraulic pressure is lost in one of the two braking systems.

A hydraulic pressure failure-warning switch monitors the primary and secondary systems for loss of hydraulic pressure.
If a significant difference in hydraulic pressure develops between the systems, the switch illuminates the red brake warning light on the instrument panel.

A combination brake warning and pressure-limiting valve is usually built into systems incorporating front disc and rear drum brakes. The combination valve is designed to apply the rear brakes slightly before it applies the front brakes.

The combination valve also limits hydraulic pressure to the rear drum brakes to prevent rear-wheel lockup during emergency braking conditions. The need for this valve has been reduced on vehicles with anti-lock braking systems because the ABS computer senses wheel lock-up and limits hydraulic pressure to the offending wheels.

Unless the combination valve has suffered severe internal corrosion, the valve is normally very 3: traces of fluid leakage where the master cylinder attaches to the brake booster indicate that the master cylinder’s rear piston seal is worn.

Time to Replace
Although modern master cylinders are reliable, they do require periodic inspection. Most modern cylinders incorporate a semi-transparent fluid reservoir that allows the fluid level to be inspected without exposing the brake fluid to moisture and dirt by removing the sealed filler cap.

In addition, many master cylinders incorporate a fluid level warning device in the reservoir that warns the driver of a low fluid level by illuminating a red “brake” warning light. A low fluid level on most anti-lock braking systems will illuminate the red brake and the orange “ABS” warning lights on the instrument cluster.

A low fluid level indicates that the disc brake pads are severely worn or that fluid is leaking from the system. If the reservoir is heavily sludged, the fluid is contaminated with petroleum solvents and/or atmospheric-born moisture.

A swollen reservoir cap seal indicates that petroleum-based lubricants or solvents have been introduced in the system. A replacement of all rubber parts or major components in the conventional hydraulic and anti-lock braking systems is usually required to repair this condition.

photo 4: bench-bleeding a new master cylinder reduces the possibility of introducing air bubbles into the vehicle’s abs system. Diagnosing Problems
When diagnosing master cylinders, keep in mind that the master cylinder is but one component of the braking system.
In addition, practically all modern ABS systems, no matter how sophisticated, are based upon a conventional hydraulic braking system using a master cylinder, hydraulic brake lines, disc brake calipers and wheel cylinders to force the friction lining against a rotating brake rotor or drum.

Note: If the ABS electronics fail, the braking system reverts to conventional operation.

Low or sinking brake pedals and the red “brake” warning light illuminating on the instrument cluster characterize most master cylinder failures.

When diagnosing low brake pedals, remember that most manufacturers provide pedal-to-floor height specifications. Low pedal height can be caused by a ­hydraulic failure in the primary or secondary system or excess clearance developing between the friction lining and disc or drum friction surfaces.

This excess clearance can be caused by a loose wheel bearing on disc brakes or a malfunctioning self-adjusting assembly on drum brakes. The most direct method of locating loose bearings or adjustor linkage is to apply the park brake.

If applying the brake increases brake pedal height, the fault lies with the axle actuated by the park brake.
A brake pedal that gradually sinks to the floor when applied indicates that the master cylinder piston seals are leaking internally or that an external leak exists in the system. External leaks are characterized by a low fluid level in the master cylinder reservoir.

If an external leak can’t be identified at the brake lines, hoses, calipers or wheel cylinders, the master cylinder might be leaking fluid from its rear piston seal directly into the vacuum brake booster (see Photo 3). The fluid is then drawn from the cylinder into the engine via the vacuum booster hose fastened to the intake manifold.

Internal master cylinder leaks can be caused by pumping the brake pedal to bleed the brakes. In this case, the piston seals are being abraded by pushing them beyond their normal range of travel onto severely corroded portions of the cylinder bore.

Internal master cylinder leaks can be pinpointed by removing the brake lines and inserting metal plugs into the master cylinder outlets or onto the metal brake lines connected to the brake hoses.

If the brake pedal continues to sink to the floor, the leakage is in the cylinder itself. If the pedal becomes solid, a ballooning brake hose might on rare occasion, cause the sinking condition.

Ballooning or other signs of decomposition in rubber brake parts might indicate the presence of petroleum-based solvents in the brake fluid. In this case, the hoses and other rubber parts should be ­replaced.

Installation Notes
Because some modern ABS ­systems might require a bi-directional scan tool to bleed the systems, it’s always best to avoid injecting air into the system by bench-bleeding the master cylinder before installation (see Photo 4).

Most new master cylinders include a bench-bleeding kit that will purge air from the cylinder bore. A narrow punch or old pushrod should be used to stroke the piston the full length of travel. Make sure that the piston returns to the full rest position.

If the piston sticks, the cylinder should be rejected. After mounting the cylinder, leave the brake lines loose to help purge air from the connections.

In many cases, the air can be purged by simply tapping on the metal brake lines. In other cases, the air can be purged by collapsing a brake caliper piston a small amount to back-flush a small amount of fluid into the cylinder bore.

After the cylinder connections are purged of air, it’s a good policy to flush the entire system using a pressure or vacuum bleeder. Vacuum bleeders are normally the preferred method because they don’t require special reservoir adapters.

You May Also Like

Volvo AWD With Active On Demand Coupling

There are a lot of Volvos on the road, and the same-year vehicles all share the same AWD systems.

Courtesy of ImportCar by Bob Howlett

When I started driving way back in 1977, it seemed like you had to buy a truck to get a 4WD vehicle. Actually, the first 4WD car was built a long time ago in 1903 by the Spijker brothers. The first commonly produced 4WD car was built by Subaru around 1974, with the AMC ­Eagle and Audi Quattro joining the party around 1980. Volvo came out with its all-wheel drive (AWD) ­vehicle in 1997. It worked pretty well, but if you didn’t ­rotate your tires and ­decided to ­install just two new tires, the size ­difference between the new tires and old tires was enough to chew up the differential. It was recommended that if you had a tire ­problem and needed just one tire, that you ­replace them all.

Understanding Underhood Parts for Hybrids

Anything that can happen to an ICE in a standard vehicle can happen to an ICE in a hybrid.

High-Pressure GDI Fuel Pumps

When solving a fuel pump issue, the scan tool is your best friend.

Diagnosing Misfires

What if there are no codes and a misfire is intermittent? This is where it gets complicated. 

Installing New Rotors

Knowing if and why there’s runout will help you reinstall a smooth braking system.

Other Posts
Diagnosing Driveability Problems

Understanding what comes out through the exhaust valve is critical to solving any emissions or driveability problem.

Ball Joint Inspection

It’s important to remember not to miss a worn joint. If a ball joint fails, the driver loses control of the vehicle.

Electronic Throttle Body Service

On most systems, idle speed is completely controlled by the throttle plate angle.

Spark Plug Replacement

Here are some tips to follow when replacing a spark plug.