Improve Diagnostic Skills By Listening Better

Improve Diagnostic Skills By Listening Better

Great service advisors focus 100% on the customer’s complaint and ask “when” and “where” questions.

The two most powerful words in a shop are “customer states.” This simple phrase has been turned into internet memes and TikTok videos. But, to a service advisor or technician, it is a phrase that is the start of all diagnostic processes.

The one trait shared by all great service advisors is that they let the customer talk. They don’t try to solve the customer’s concerns or explain what the problem might be or even how a car works. Instead, they ask questions and record the customer’s concerns. That is all.

Letting the customer talk can be challenging for service advisors who are “recovering” technicians. It is challenging because all ex-technicians want to come up with a diagnosis as quickly as possible. It is part of their flat-rate DNA. Great service advisors focus 100% on the customer’s complaint and ask “when” and “where” questions that could help a technician replicate the problem.

Rookie service advisors will say, “It could be the…” This opens you up for the follow-up question, “How much will that cost?” This sets an expectation with the customer that a repair should cost only that much, and they will usually start asking around how much that will cost at another shop.

The next most valuable trait of a great service advisor is they repeat the customer’s concern back to them. This establishes trust with the customer because you just reflected their words back at them. As a result, they feel like they are being taken seriously. 

You might think it is a waste of time, but repeating the customer’s complaint has significant benefits. Just try it when your partner is complaining about something you have done. Even if you disagree with their grievance, they will feel better that you might understand their plight. 

The last trait of a great service advisor is they write down all the details for the technician. These notes do not have to use complete sentences with proper grammar or even seen by the customer. Instead, you can use bullet points to document the details. Remember, repair orders are not an essay, and you are not being graded. 

Anybody can be a successful service advisor if they follow the three steps of listening, repeating and writing. Even if a service advisor or technician has a limited technical background, if they use the three steps, they will always be able to sell diagnostic labor. It is like a Jedi mind trick.

If you are a technician, you must put every word under a microscope and not dismiss a single detail. Never assume the customer is full of crap. Remember, the owner will spend more time behind the wheel of their vehicle than you ever will.

The next step is to verify the complaint. If the problem is happening all the time, it will be easy. If the problem is intermittent, you should replicate the conditions when the complaint occurs within reason. Skipping the notes and going right for a scan tool to get the codes will often lead to misdiagnosis.

Great technicians will use the word “confirmed” on notes to the service writer. They do not guess that a repair will solve the initial complaint. A technician should never guess. They always confirm the diagnosis with specific tests and procedures. These tests and procedures put a tangible value on diagnostic labor charges.

You May Also Like

Ball Joint Inspection

It’s important to remember not to miss a worn joint. If a ball joint fails, the driver loses control of the vehicle.

Don’t miss a worn joint!

Detecting and measuring wear in a ball joint is critical to ensuring the safety of a vehicle. 

Types of Ball Joints

A ball joint is made up of a housing, ball stud, bearings, end cover and Belleville washer or spring. A Belleville washer is a conical-shaped spring designed to be loaded in the axial direction. The joint is attached to a control arm by pressing or riveting the joint into the arm. If the joint is pressed into the arm, it will require a special tool to remove the old joint and install the new one. 

Ignition System Do’s and Don’ts

Why do ignition systems give technicians problems when diagnosing ignition-related misfires? The answer is that some technicians use tests that might give inconclusive results or do damage to the coil or drivers inside a module.

BMW N54 Cooling System Problems

Let’s take a closer look at this water pump, how to replace it efficiently and what other components should be replaced along with it.

BMW Dual Clutch Transmissions

BMW uses a wet clutch with separate inboard and outboard sections for the two sub-transmissions.

Brake Pad Edge Codes – What Can They Tell You?

The “Edge Code” can tell you information about a brake pad’s friction material.

Other Posts

A Closer Look At Key Programming

When it comes to key programming, there are different levels of security access depending on the year, make and model of the vehicle.

Steering Angle Sensor Service

Ninety percent of the time when a steering angle sensor code is active, it means the sensor needs to be calibrated.

Belt Service For Hybrid and Stop/Start Systems

Knowing how to “force start” a hybrid vehicle can be helpful if you are trying to diagnose a noise problem that involves the accessory belt drive system.

Fuel Pumps and Cranking

Diagnosing the problem comes down to understanding what causes a loss of fuel pressure.