Worn Wheel Hub Bearing Symptoms -

Worn Wheel Hub Bearing Symptoms

Driving conditions and installation practices can damage a worn hub. These symptoms often indicate wheel bearing damage.

timken-wheel-hub1Snapping, Clicking or Popping

These noises are typically heard when making sharp turns and can indicate excessive bearing endplay from inadequate clamping. They can also indicate a worn or damaged outer CV-joint.

Grinding When in Motion

This noise is normally heard when turning or when there is a shift in load. This can suggest a loss of integrity, such as roller or raceway damage, but typically means mechanical damage in a wheel-end system.

Knocking or Clunking

These noises are normally heard when shifting — either when changing directions or when transitioning from accelerating to coasting. These noises can signal excessive play in the CV-joints or U-joints, or excessive backlash in the differential gears — a condition not generally associated with bearings.

Humming, Rumbling or Growling

These noises are normally associated with tire, electrical or drivetrain components. If bearing-related, the noise or vibration presents itself when driving in a straight line, but intensifies when slightly turning the steering wheel. Typically, the side opposite the rumbling is the defective side.

Wheel Vibration and/or Wobble

This associates with severe chassis misalignment or a damaged or worn tire, wheel or suspension component. When related to the hub or bearing, this can indicate a mechanically damaged bearing or improperly torqued lug nuts.

Shudder, Shimmy or Vibration at a Constant Speed

These sensations associate with worn or damaged suspension components or tires that are out-of balance or out-of-round. It is not normally indicative of hub or bearing damage.

Abnormal Side Pull When Brakes are Applied

Severe bearing looseness can cause excessive runout, making the brakes pulsate or pull. However, this usually indicates a defective caliper or equalizer and can also be a sign of worn brakes or rotors. The most common cause is a warped rotor due to the caliper not retracting.

Uneven Rotor or Brake Pad Wear

This normally indicates a bad caliper and/or a bad equalizer, which is not bearing related. The most common cause is a warped rotor due to the caliper not retracting. Severe looseness related to a worn or damaged bearing can cause excessive runout, leading to uneven wear on the brake pads and/or rotor.

Abnormal or Uneven Tire Wear

The most common causes of abnormal tire wear include worn or damaged suspension components, misalignment and improper tire inflation or selection. Extreme bearing wear or looseness can cause abnormal tire wear, but it is typically related to other failure modes.

ABS Failure

In extreme cases, too much endplay creates excessive movement that damages internal and external sensors. This indicates a lack or loss of bearing clamp, resulting from severe mechanical break up, external corrosion or damage.

Courtesy of Timken Tech Series.

You May Also Like

Diagnosing Misfires

What if there are no codes and a misfire is intermittent? This is where it gets complicated. 

What is a misfire? Is a misfire when the cylinder does not fire? Is it when the cylinder fires too soon or too late? The answer is “yes” to both questions. Some misfire complaints are a flashing check engine light, and a P0300 to P0312 diagnostic trouble code (DTC) indicates that one or more cylinders are misfiring. This is the easiest misfire to diagnose. But, what if there are no codes and a misfire is intermittent? This is where it gets complicated. 

Installing New Rotors

Knowing if and why there’s runout will help you reinstall a smooth braking system.

Diagnosing Driveability Problems

Understanding what comes out through the exhaust valve is critical to solving any emissions or driveability problem.

Ball Joint Inspection

It’s important to remember not to miss a worn joint. If a ball joint fails, the driver loses control of the vehicle.

Electronic Throttle Body Service

On most systems, idle speed is completely controlled by the throttle plate angle.

Other Posts
Spark Plug Replacement

Here are some tips to follow when replacing a spark plug.

Transmission Fluid Hydraulics

You need to know how transmission fluid flows inside an automatic transmission.

How ADAS Systems Perform

When new technologies are applied to driver safety, a higher level of scrutiny and service is required.

Air Ride Suspension Diagnostics

The key to understanding the embedded logic of air ride systems is using service information.