Wheel Bearing or Hub Replace

10 Things To Know About Wheel Bearings

Wheel bearings keep the world rolling by reducing friction and allowing the wheels and axles to spin while a vehicle is in motion.

Wheel bearings keep the world rolling by reducing friction and allowing the wheels and axles to spin while a vehicle is in motion. The wheel bearings also support the weight of the vehicle, and must withstand the side forces that occur when cornering. These forces can be quite severe and may lead to early wheel bearing failure if the original equipment bearings are not designed for extended hard driving (think police car, taxi, pizza delivery, racing, etc.).

  1. Most wheel bearings should last upward of 150,000 miles or more with normal driving, and many will last the entire life of the vehicle without failing. But some don’t go the distance, and the reason why is usually corrosion or abrasive wear.
  2. Wheel bearings live in a sealed environment. Most wheel bearings on late-model vehicles are part of a sealed hub assembly or cartridge. Sealed hub assemblies may be used on Front-Wheel Drive (FWD) as well as Rear-Wheel Drive (RWD) cars and trucks, while cartridges are often used in the knuckles of FWD cars. Sealed hubs and cartridges require no periodic maintenance or adjustments. But on older vehicles with serviceable wheel bearings, the bearings should removed, cleaned, inspected and regreased every couple of years.
  3. If outside contaminants such as water, road salt or dirt get past the seals, they can ruin a wheel bearing within a few thousand miles or less. Driving through hub deep water may force water past the seals.
  4. Ball bearings and roller bearings both have highly polished hardened surfaces and close clearances so they can’t tolerate much abrasive wear or pitting caused by rust. Severe overloading can cause surface spalling (flaking) and/or cracking in a bearing, but that’s seldom seen in low mileage bearing failures unless a vehicle has been subjected to some type of abuse.
  5. “Brinelling” is another condition that may occur if the bearings are subjected to high impact loads or vibrations. Brinelling will leave small indentations in the surfaces of the races and rollers.
  6. Heat discoloration (typically a bluish color) is usually the result of loss of lubrication or overloading. Overheating can soften the rollers and races leading to accelerated wear and rapid failure.
  7. A sure sign of impending wheel bearing failure is noise, looseness (play that exceeds .003 to .004 inches) and/or grease streaks radiating outward from the seals. A bad wheel bearing may whine, hum, rumble, growl, chirp or squeal. The sound may come or go, but usually increases with vehicle speed.
  8. A bad wheel bearing should always be replaced without delay because a bearing failure can cause the loss of a wheel or axle.
  9. On some vehicles, the sealed wheel bearing and hub assembly also contain a built-in wheel speed sensor for the antilock brake system. If this sensor fails, it will turn on the ABS warning light and disable the ABS system until the sensor is replaced. But the sensor cannot be replaced separately on these applications. The entire hub assembly must be changed.
  10. Hub units are expensive to replace. Even so, if one has failed the others may be nearing the end of their service life too. Replacing wheel bearings in sets (both fronts, both rears or all four) may be recommended to reduce the risk of bearing failures down the road.
  11. If a customer needs grease for an older vehicle with serviceable wheel bearings, make sure they get a high-temperature wheel bearing grease such as No. 2 NLGI lithium-based grease or a synthetic wheel bearing grease. Ordinary chassis grease must never be used to lubricate wheel bearings. Also, the old grease seals should be discarded and replaced with new ones. Old seals usually leak if reused, which can lead to a loss of lubrication and bearing contamination.

You May Also Like

Differences in Brake Fluid Matter To Cars – And Owners

Though DOT 3, 4 and 5.1 brake fluids are technically compatible with each other, when mixed, fluid properties can change.

Trying to match the brake fluid to a product that is available can quickly have your head spinning when trying to service a late-model BMW, VW or Mercedes. Finding the correct specification can be ambiguous because some manufacturers provide a part number instead of a specification in the service information or owner’s manual. Brake fluids can have several confusing names like LV, Super or DOT 4 Plus.

Brake Hardware

Specific hardware does not do its job if it is left in the box.

Throttle-By-Wire Diagnostics

On older throttle cable systems, the carburetor or fuel injection system reacted to the throttle angle.

Spotting Brake System Failures By Inspecting The Old Pads

The main culprit of friction material separation is typically corrosion.

Diagnostic Strategies For Stop/Start Systems

This function of the power management system uses several modules to decide when the engine needs to stop and start.

Other Posts

Brake Pad Ecology

The leading source of particulate emissions come from brake pads and tires.

Lightweight Brake Components

Engineering teams have certain goals that they need to meet or exceed.

Power Steering Pull

Every driver has a different threshold for a pull.

Fuel Pressure Diagnostic Service

Use a scan tool that can look at special direct fuel injection parameters and perform bidirectional tests.