Alternator Voltage and Battery Test (Undercharging and Overcharging)

13 Alternator And Battery Testing And Diagnostic Tips

If only battery voltage is present at the battery on a running engine, does this mean the alternator is "bad?" No, it does not. That only means that the alternator is not charging, but does not reveal why. Therefore, it does not prove a faulty ­alternator.

1. One Test Is Not Enough

If only battery voltage is present at the battery on a running engine, does this mean the alternator is “bad?” No, it does not. That only means that the alternator is not charging, but does not reveal why. Therefore, it does not prove a faulty ­alternator. All too often the ­alternator is condemned by ­technicians due to this test alone.

2. Look It Up

For some, it’s normal to see as high as 16 volts for long periods at a time. For others, it’s ­normal to see as low as 13 volts. For some, a constant 13.6 volts is an indication of a problem. Still yet, it’s perfectly normal for others to see the alternator not charge at all intermittently. Some alternators are controlled only with an internal or external regulator. Some are controlled only by the PCM. Still yet, others are controlled by a voltage regulator and the PCM. Not knowing what controls what, and how it is supposed to function, can’t cause a ­misdiagnosis or cause a critical problem to be over looked. Take the time to look at the service information.

3. Extra Ground, Extra Trouble (Codes)

It is a bad practice to use the positive and negative battery terminals to power aftermarket accessories on some vehicles. The extra connections can cause the battery to incorrectly report the state of discharge, despite a normal battery condition. This can cause the battery to be overcharged and/or codes to be set that may cause the charging light on the instrument cluster to illuminate.

4. Alternator Communication Lost

If communications were lost between the PCM and alternator, the PCM would turn on the battery light, but the regulator would still charge the alternator at about 13.6 volts. The PCM would set a trouble code relating to that loss of communication. Imagine trying to diagnose a battery light that doesn’t appear to have any reason to be on. That is, it doesn’t appear to have a valid reason until a scanner is added to the testing.

5. Load Testing + Low Speeds = Toasty Alternator

Although load-testing an alternator provides a quick way to test for drive belt slippage, keep in mind that an alternator can easily be overheated when testing for maximum output during low-speed operation for an extended period of time. Most alternators will not be able to keep up with the load when idling and the lack of cooling compounds the problem even further.

6. Higher-Than-Rated Batteries

Because new batteries typically test as much as 25% higher than their rated capacities, a recently replaced battery with a bad cell can occasionally pass both a conductance and a load

7. Bad Cell Lowers Charging Voltage

Because normal charging voltage can’t be achieved on a battery with a bad cell, the alternator will overcharge the remaining cells and boil the electrolyte. At the other extreme, a battery that is sulfated due to being undercharged or not seeing constant use will maintain normal charging voltages. The symptoms of a sulfated battery are that it charges very quickly and produces a very low amperage discharge rate.

8. Check The Pulley

Many late-model vehicles use a decoupler pulley on the alternator. These new pulleys allow the alternator to “free-wheel” or “overrun” when the belt suddenly slows down. This prevents the belt from slipping and reduces vibration. Best of all, the system needs less tension and even a narrower belt can be used. This can result in a 1.5% to 2% fuel economy improvement. However, these pulleys have a limited lifespan due to how they operate internally.

Some replacement alternators will not come with a pulley or a solid pulley. If the replacement alternator does not come with a new pulley, be sure to install the correct pulley with it. If not, the replacement alternator can fail sooner than expected.

0-Alternator

9. Put The Car To Bed Before Testing For Parasitic Draw

As a rule, the key-off current drain on most late-model vehicles should be less than 50 milliamps (mA). But on some vehicles it might be normal to have even greater draws for up to 10 minutes after the keys have been removed from the ignition. During this period, the serial data buses could be communicating and performing some digital housekeeping. Also, systems like air ride, the evaporative emissions system and auxiliary water pumps could still be active long after the vehicle has been parked. This is why on some modern vehicles service information, an OBDII breakout box and a scan tool are necessary to solve some intermittent parasitic power drains.

10. Check The Connections

If you don’t see at least 13.5 volts when you check charging voltage at the battery with the engine idling, check the wiring connections at the alternator — not just visually or by wiggling the wires or connectors, but check for excessive resistance by doing a voltage drop test. Many so-called alternator problems turn out to be nothing more than a bad connection at the alternator or a bad wiring harness.

11. Milliamps — Not Amps

On many vehicles, the PCM is controlling the duty cycle of the alternator. It is controlling the amps and voltages in finer increments than can be measured by a simple meter, so that current is supplied in a more efficient manner. These changes might be just 10 milliamps, so connections to the regulator are critical. You cannot afford a mediocre connection.

12. Low-RPM Alternators And Transmissions

Automatic transmissions with five or six speeds can drastically reduce engine speed when cruising. Many modern engines operate well under 2,000 rpm until they reach highway speeds of about 60 to 70 mph. Consequently, if the alternator doesn’t maintain rated charging voltage at lower engine speeds, the battery will discharge under heavy accessory loads. In most cases of undercharging, the alternator may have an incorrect diameter pulley installed, the drive belt may be slipping or the alternator itself might be undercapacity for the vehicle application.

13. Temperature Sensing Alternators And Batteries

Depending upon ambient temperature, charging voltage generally varies between 14.8 and 13.5 volts. The actual charging voltage designed into a voltage regulator is dependent upon factors such as how far the alternator is located from the battery and the ambient air temperature surrounding the battery as calculated by the PCM. Under normal operating conditions, an alternator should maintain about 14.2 volts at 70° F ambient air temperature.

Courtesy Underhood Service.

You May Also Like

Ignition Coil Output

To see inductance inside the primary windings, use an amp probe placed around the positive wire for the ignition coil.

Kilovolts or kV is the unit used to measure the output of an ignition coil. Some coils can output 20kV to 40 kV. So, how does an ignition coil turn system or battery voltage into these huge voltages? The answer is inductance. 

The ECM provides the voltage to the primary coil winding. The primary winding might have 100 turns around the coil’s core or plates. When the voltage to the coil is turned off, a magnetic field collapses. The collapsing field will generate more than 100 volts thanks to inductance. The energy is transformed by the windings in the secondary with inductance again, but thanks to the 10,000 windings, the voltage is boosted to 40kV at the spark plug’s electrodes. The best way to see inductance inside the primary windings is to use an amp probe placed around the positive wire for the ignition coil. With this setup, you can see the current ramping in the coil and the collapse of the magnetic field. 

Maximize Your Scan Tool

Are you maximizing your scan tools to their full potential? Don’t let them be just an expensive code reader.

Air Ride Conversion Kits

Air ride and active shocks and struts will eventually fail – succumbing to either damage to or dry rot of the air spring.

Nylon Fuel Line Repair Techniques

Can you repair fuel lines yourself? Yes, if you make quality your number one priority when making decisions.

Understanding Differences Between Aluminum And Cast Iron

Sheer material differences aside, what are the features and benefits of aluminum and iron engine components?

Other Posts

Wheel Speed Sensors and Bearings

The only way to diagnose the sensor and circuit is with a scan tool or scope. 

Timing Chain Systems Need Clean, Quality Oil

Using the wrong oil causes a vehicle’s timing chain to wear quicker.

Threadlocking Compounds For Vehicle Corners

To get the most out of these “liquid” tools, you first need to know how they work.

Battery Charging and Programming Diagnostics

Temperature changes how the battery discharges and the amount of current that can be delivered.