AC Condensers

AC Condensers

The characteristics that make the parallel-flow condenser so efficient are among its major drawbacks as well.

the question for most technicians is whether to flush the condenser or replace it. The answer depends on the type of condenser it is. For tube and fin condensers or serpentine types, the choice is not difficult; the internal tube diameter is wide enough to be able to flush material through it to ensure the inside is clean and free of contaminants.

Starting in the early 2000s, the most popular type of condenser for vehicles that use R-134a has been the parallel-flow condenser, because it’s a more efficient condenser design for this type of refrigerant. Parallel-flow condensers don’t have a large hollow tube that the refrigerant flows through, but a series of very small tubes close together in a row with the internal diameter about the size of a pin head. This helps to improve the surface area of the condenser and increase its cooling capacity.

Its multi-channel construction allows the refrigerant to make multiple passes through the condenser, which provides maximum heat transfer. Also, the smaller tubes and wide surface area allow the maximum amount of refrigerant to encounter air flowing through the condenser fins.

Unfortunately, the characteristics that make the parallel-flow condenser so efficient are among its major drawbacks, as well.  

The tubes that efficiently transfer heat are so small that they trap any contamination in the system that tries to pass through them. What that means for your customers is that flushing the A/C system won’t remove the contamination from the condenser. These particles will create a restriction in the condenser and make the high-side pressures go up, forcing the compressor to work harder and possibly fail. It’s also possible that the contamination in the condenser can work itself free and end up at the compressor, where it also will cause a failure.

Nonetheless, the parallel-flow condenser is a highly effective heat exchanger that divides the unit into sections or “passes” which creates a more efficient process for the refrigerant to change state from gas to liquid.

This is done by making the refrigerant change direction by 180° at the end on the siderails by placing a plug inside the rail at intervals, forcing the refrigerant to change directions. The more plugs, the more times the refrigerant changes direction. In most condensers, the refrigerant makes three to four “passes” through the condenser.

When a compressor fails, it introduces contaminants into the system. One of the easiest ways to spot this is to remove the orifice tube that usually reveals metal deposits or sludge from a faulty compressor. The metal and sludge get deposited throughout the system and will collect at places in the system with restrictions, like the orifice tube and, on later-model vehicles, the parallel flow condensers.

While flushing the system can help to remove debris from part of the system, items with small openings, like the parallel flow condenser are going to collect the debris. Flushing them will only push the contaminants further into the condenser and will collect at the plugs in the side rails, reducing the amount of rows available to cool the refrigerant and slowing the flow of the refrigerant; this leads to high head pressures. Combine that with a high-efficiency compressor, like a scroll, and not only will the replacement compressor fail, but it may do so catastrophically.

When confronted with a compressor failure on a vehicle fitted with a parallel-flow condenser, experts recommend that the technician replace the accumulator, orifice tube or expansion device and condenser. It is also recommended that all other components be flushed to ensure they are free of contaminants that could harm the new compressor.

Parallel-flow condensers don’t have a large, hollow tube that the refrigerant flows through, but a series of very small tubes close together in a row with the internal diameter about the size of a pin head. This helps to improve the surface area of the condenser and increase its cooling capacity.

Here’s the bottom line: If your customer’s A/C system has a parallel-flow condenser, and there’s a situation where you need to flush the system, it’s strongly recommended that you replace the condenser. That’s because a parallel-flow condenser cannot be flushed. Since flushing the system is always recommended when replacing a failed compressor, if your customer needs a new compressor, odds are they’ll need a new condenser, too.

Be aware, sometimes the problem isn’t what it appears to be. 

In this example of the necessity of careful diagnostic procedures, the owner of a 2008 Nissan complained of cooling issues.

The power steering pressure switch communicates with the engine control unit (ECU) to regulate the vehicle’s power steering system. When the power steering pressure switch detects excess load, the ECU makes adjustments to the power steering system to reduce stress on the motor.

In this case, what appeared to be an air conditioning issue on a 2008 Nissan Altima 3.5L, ended up being a direct result of excess stress on the power steering system after a wheel and tire upgrade. When the factory wheels were replaced with a larger style, the diameter of the new wheels increased the load going “side to side”. Because this vehicle is designed with a shared serpentine belt for the A/C system and power steering pump, the A/C system appeared to be malfunctioning because the ECU was directed to reduce stress at the power steering pump. The solution to this problem was simply to replace the power steering pressure switch.

You May Also Like

Transmission Valve Body Service

Four basic items are necessary to start your own reprogramming ventures.

The conversation goes like this: I have been paying mobile programmers or remote access programmers (RAPs) far too long. I believe I can save money and time by doing this myself. What type of equipment is needed and what is the cost to get up and running?

Let’s find out! In a nutshell, four basic items are necessary to start your own reprogramming ventures. You may even have some of these items on hand already.

Fuel Pumps and Cranking

Diagnosing the problem comes down to understanding what causes a loss of fuel pressure.

ADAS and Vehicle Alignment

New vehicle ADAS features all rely on the alignment being exactly as it should be.

PCV System DTC

PCV systems control crankcase pressure.

A/C Condenser Clogs

When a compressor fails, the question for most technicians is whether to flush the condenser or replace it.

Other Posts

ADAS False Activation Evolution

The logic behind most ADAS warnings or corrections is to examine the plausibility of the situation.

Checking The Auxiliary Water Pump

A car or truck comes into the shop with a complaint of poor heater performance. The issue may be the auxiliary water pump.

Tech holds up heater core
It’s Got Spark!

Why can’t you trust some spark tests?

ADAS Calibration Aborts

Troubleshooting the problem comes down to knowing the failure, vehicle or fixtures.