What Constitutes A Complete Brake Job?

What Constitutes A Complete Brake Job?

Complete, safe brake jobs are key. This video is part of the Group Training Academy.

You may face a customer asking for the bare minimum when it comes to a brake repair. Whether it’s just a set of pads on the front, a single rotor or drum, a caliper or wheel cylinder, a brake hose or a master cylinder, you may hear “Fix only what’s broken so my car stops.”

This cost savings approach to brake repair is likely to be more expensive in the long run, of course, because each component is part of a total system that only functions as well as the weakest link. The weak link today might be a worn set of pads or a leaky caliper. But what’s going to be the weak link tomorrow or the day after or six months down the road?

Replacement parts, such as brake pads and shoes, should equal or exceed the performance of the OEM parts. Quality aftermarket brake suppliers go to great lengths to make sure their replacement linings meet or exceed the OEM requirements, delivering the same friction characteristics, stopping power, fade resistance, pedal feel and longevity as the OEM pads. If they don’t, it can upset the operation of the ABS system and have an adverse effect on braking.

When brake repairs are needed, the best approach is to thoroughly inspect the entire brake system and replace any parts that are necessary to restore the brakes to like-new condition.

On ABS-equipped vehicles, a thorough system inspection should start by turning on the ignition to verify that the ABS warning light circuit works. The ABS light should come on for a few seconds, then go out if everything’s fine.

No ABS warning light? Then either the bulb needs to be replaced or there is a wiring or control module fault. If the ABS light comes on and remains on (does not go out), further diagnosis will be required to determine what’s wrong with the ABS system. On most vehicles, this will require using a scan tool to access the ABS codes and check ABS inputs and outputs.

The next check is the brake fluid inside the master cylinder reservoir. A low level may indicate a leak or worn linings. Discoloration indicates moisture contamination and the need for a fluid change. Chemical test strips are available to test the condition of the fluid. The fluid should also be changed when the brakes are relined to remove moisture and restore corrosion protection.

Next comes the linings. The thickness of the front pads should be measured. If worn down to minimum specifications or if wear indicators are making contact with the rotor, new linings are needed. If the pads are still above the minimum specs, but are worn, replacing them now may save the rotors. Other valid reasons for replacing a set of pads, regardless of their thickness, would be noise, damage or contamination from brake fluid or grease).

Rotors must be relatively smooth and free from cracks, hard spots and excessive runout. Deep scratches or grooves indicate a need for resurfacing unless they are already worn too thin.

Calipers must be leak-free, have dust boots that are free from cracks, and operate normally. Uneven pad wear (inner pad worn more than the outer pad) is a clue that the caliper is sticking. Calipers that are leaking or damaged must be rebuilt or replaced (the same goes for wheel cylinders). Equally important is the disc brake hardware — and lubricating the caliper bushings and slides with a long-lasting, high-temperature brake lubricant.

Drums must be removed to inspect the rear shoes. If the linings are at or below minimum specifications, new shoes are needed. The condition of the brake hardware is also important. Springs that are stretched, broken, badly corroded or badly discolored from heat should be replaced. Self-adjusters should operate correctly and be free from corrosion. Hardware should be replaced when new linings are installed. The inside of the drums must be clean, smooth and flat. Minor wear can be corrected by turning the drums, but if the drums are cracked, out-of-round, bellmouthed or are worn excessively, new drums are needed.

All brake lines and hoses should be inspected for leaks. Any hoses that are cracked, leaking, worn or swell under pressure must be replaced. Finally, check the operation of the parking brake and brake lights.

Good brakes are absolutely essential for safe driving. So be sure to remind your customer of the importance of inspecting all the parts in the brake system, not just the part that failed.

You May Also Like

Learn How To Safely Lift HEVs and BEVs

If you can’t lift a vehicle without damage, you will not be able to unlock this service opportunity in this growing segment.

Most HEV and EV vehicle repairs are not those done to battery packs or electric motors. Instead, the most significant repair opportunities are tires, brakes, and suspension. And if you can’t lift a vehicle without damage, you will not be able to unlock this service opportunity in this growing segment. The stakes are higher for EVs and hybrids because if a lift arm or adapter is not correctly placed, it could damage an expensive battery pack mounted under the vehicle. Some of these battery packs can cost five figures to replace. Also, there is a fire hazard. If a battery pack is impacted or punctured, never guess where or how to pick up a vehicle. A vehicle’s owner’s manual or service manual often will provide guidance on where to find and how to access the appropriate jacking and lifting points. Some EVs and HVS have specific lift points stamped into the unibody.

Understanding LSPI & Engine Oil

Discover the importance of using the correct oil specification for your vehicle.

Understanding Air Suspension

We explore the evolution and functionality of air suspension systems for vehicles.

Suspension Bushings: Role, Materials, and Wear Indicators

Regular inspection and timely replacement of worn bushings are crucial for optimal vehicle performance and safety.

Randy Breaux, Group President, GPC North America, Talks to AMN Drivetime

At NAPA, “Breaux Knows” business relationships, ABCs to avoid, and serving the automotive professional.

Other Posts
Serpentine Belt and Drive System Maintenance

Properly maintaining the entire drive system prevents premature belt wear and system failure, ensuring customer satisfaction and vehicle reliability.

EGR Systems: Understanding Exhaust Gas Recirculation

Learn how it works, its history, and its impact on both performance and the environment.

Advanced Cooling System Technologies: Hybrid & EVs

Learn how to keep your hybrid or electric vehicle running smoothly and efficiently.

Do EVs Require Special Brake Pads?

Proper brake pad selection is crucial for EVs to ensure consistent stopping power and long pad life.