Serpentine Service Typically Involves More Than Just The Belt

Serpentine Service Typically Involves More Than Just The Belt

Your attention to belt condition will ensure systems are operating effectively. Sponsored by The Group Training Academy.

Certain components typically last a long, long time – your customer might not experience a serpentine belt replacement until their car or truck reaches 60,000-100,000 miles after it was installed at the factory during the vehicle’s assembly. 

Your service advisors should remember that, because the average age of vehicles today is in the 12-to-13-year range, many vehicles are being driven much longer than that. And light duty vehicles are being driven 12,000 to 14,000 miles a year (on average).      

A serpentine belt system has a service life somewhere in the 90K range.        

That puts a serpentine belt replacement at about the 6 year mark – halfway through an average vehicles life – with many more miles to go.

So, once they’ve had ONE belt replaced, your customers will likely see the need for another one at some point. Here’s what’s often misunderstood:

While they may expect the same service from a replacement belt, in many cases, they’ll actually see significantly fewer miles of service because a complete service is not being performed.

It’s likely NOT the fault of the replacement belt because you’re not dealing with a single component, the belt, you’re dealing with a system. The serpentine drive belt system is actually made up of a set of sub-systems designed to work together and be replaced together. The belt will see different stresses and loads depending on the accessory being driven during the operation of the vehicle.

Your tech may have suggested belt replacement for a variety of reasons including normal wear (usually revealed using a belt wear gauge), hearing belt squeak because of belt elongation, a worn tensioner, misalignment or because there was visible contamination from petroleum products.

In addition to driving different components, the belt is in constant contact with tensioners and pulleys. These components are designed with the same lifespan as the belt and when they are worn or damaged they can actually shorten the life of a new belt.

A belt tensioner is spring-loaded, and the constant movement of the tensioner will wear down the spring’s ability to apply the correct amount of force to the belt. A belt without the appropriate force applied will not effectively drive the accessory pulleys which creates an inefficient transfer of power, underperforming accessories and accelerated wear of the newly installed belt. Tensioners also dampen the impulses created by the engine, and when the damper fails, the belt begins to hammer the accessories in the system.

Idler pulleys and tensioner pulleys have sealed ball bearings and are designed with the same service life as a typical serpentine belt. A worn-out bearing can cause the pulley to operate at an abnormal angle, creating excessive wear on one side of the belt. 

A seized pulley can break off its mount, causing the belt to ride off the pulleys. Even if it isn’t broken, a misaligned pulley can cause an annoying chirp and actually accelerate belt wear. Misalignment is the number one cause of belt chirp on serpentine belt systems, say experts.

As the vehicles in operation continue to get older, you’ll likely see more and more customers surprised to know they’re having belt issues. The first step is to accurately inspect the system.

By doing so, you can uncover if you have one or more belt-eating culprits such as parallel or angular misalignment. Pulley run-out is misalignment from a bent component shaft or worn bearings. During your inspection, keep an eye out for bent or broken accessory brackets, and look for loose, missing or broken bolts – these items will contribute to belt alignment issues.

In addition, be sure fluid leaks are addressed at the time of belt replacement. Petroleum-based fluids will soften belt material, causing the belt to weaken, wear faster and, in some cases, cause belt delamination. Along with oil-based leaks, a coolant leak might not cause physical belt damage but will cause the belt to slip on the pulleys. The slippage will cause the belt to wear and add heat to the belt which can result in premature belt failure.

Of course, older vehicles aren’t the only ones at risk. Today’s hybrids and electric vehicles require precision function of all their components to maximize their efficiency. Your attention to belt condition will ensure drivers have the right components to keep their systems operating effectively. For more information, visit

This video is sponsored by The Group Training Academy.

You May Also Like

Installing a Knuckle Hub Assembly

Addressing tough attachment points and ensuring proper torque is critical. Sponsored by GSP North America.

Another wheel bearing. You know what you’re in for, and right away you’re thinking is it going to come out easily, or is it going to be stuck in the knuckle like it was set in concrete? And what other problems are you going to run across? How bad is the rust and corrosion going to be and will you find previous damage from incorrect installation procedures? 

What is a Performance Brake Pad? (VIDEO)

There are engineering differences between race car and production vehicle brake systems. Sponsored by Akebono Brakes.

Belt-Driven Starter Generator Systems (VIDEO)

Fuel efficiency meets power with belt-driven starter generator systems. Sponsored by The Group Training Academy.

The Importance of Maintaining Belt Tension

Maintaining proper belt tension can enhance fuel economy. Sponsored by The Group Training Academy.

Audi Driver Assistance System Front-facing Camera Calibration

Joe Keene discusses how to calibrate the front camera on an Audi Q3 after the windshield was replaced.

Other Posts

Auto Pros On The Road Visit Detroit’s Jay’s Auto

Jay Salaytah meets the expectations of his customers and the needs of his employees. This video presented by Autolite.

Sealed Units Matter (VIDEO)

By sealing the joint, engineers can use better greases and materials to increase longevity. Sponsored by TRW.

Auto Pros Visit Interstate Auto Care, Madison Heights, MI

For Bill Nalu, business is more than fixing cars – it’s about connecting with people on a personal level.

Top Five Brake Tips (VIDEO)

Here are five tips on brake jobs tips for technicians. This video is sponsored by TRW.